MATi-12

Automatic system for potentiometric titration of COD samples in series up to 21 samples. The titration is carried out directly in the reaction vessel on the rack. Afterwards, the electrode is cleaned automatically by means of the membrane pumps built into the sample changer and the reaction vessel is emptied. The control of this system is handled by the user-friendly OMNIS software.

MATi 01

PC-controlled, fully automatic water analysis system with a rapid measurement system for the precise sample transfer of 100 mL samples. After the conductivity measurement, pH value, alkalinity and Ca/Mg content are determined in an external cell. A maximum of 59 samples can be placed on the rack. The control of this system is handled by the proven OMNIS software.

MATi 08

Automated system for the performance of potentiometric titrations on acids and bases. Up to 100 samples can be placed on the sample rack. The sample is pipetted out of the beaker into the external titration vessel, after which a completely automatic determination is carried out. The volume to be pipetted can vary between 0.5 and 9.0 mL. After the titration, the external vessel is cleaned thoroughly using the membrane pumps built into the Sample Processor. The control of this completely automatic analysis system takes place using the proven OMNIS software.

MATi 02

PC-controlled, fully automatic analysis system for the direct determination of TAN or TBN values in mineral oil products in series of up to 59 samples. The analysis is carried out in accordance with ASTM standards D664 and D2896. The system is noteworthy for its special resistance to the solvents used in this application. The data acquisition and the complete control of the system takes place via the proven OMNIS software.

MATi 07

Fully automated system for the performance of potentiometric titrations such as acid/base, Redox and classic halogenide titration in series of up to 28 samples. The system is controlled with the OMNIS software. At the end of the determination, the electrode and buret tips are cleaned automatically using the Pump Station and the beaker is emptied.The electrode must be selected separately, depending on the application.

MATi 06

Fully automatic system for potentiometric titration of acids and bases in series of up to 12 samples. The titration is carried out directly in the beaker on the rack. Afterwards, the electrode is cleaned automatically using the membrane pumps built into the sample changer and the titration beaker is emptied. The control of this system is handled by the user-friendlyOMNIS software.

MATi 14

Automated system for the determination of conductivity in sterile waters in accordance with USP 645. Up to 28 samples can be placed on the rack and processed within one series. The sample is transferred from the sample beaker into the external titration cell and analyzed completely automatically in accordance with the 3-stage USP Standard procedure. The system is controlled by the OMNIS software.The thermostat for controlling the temperature of the external titration vessel must be ordered separately.

MATi 13

Automated system for the determination of the permanganate index in accordance with DIN EN ISO 8467. Up to 24 samples can be placed on the rack and processed within one series. The sample is pipetted from the sample beaker into the external titration cell and analyzed completely automatically in accordance with the requirements of the DIN standard. After the titration, the external cell is cleaned thoroughly using the membrane pumps built into the sample changer. The system is controlled by the OMNIS software.The thermostat for heating the external titration vessel must be ordered separately.

ProfIC-Vario-01-Cation

The Professional IC Vario system with direct conductivity detection enables fully automated determination of cations or anions (non-suppressed).Typical areas of application:Universal use for cation analysis; Routine analysis with large numbers of samples without additional sample preparation; Coupling with MS or ICP/MS instruments for research and development tasks; Schematic representation

ProfIC-Vario-01-Anion

The Professional IC Vario system with sequential suppression and conductivity detection enables fully automatic determination of anions or cations.Typical areas of application:Anion or cation analysis for universal use; Routine analysis with large numbers of samples without additional sample preparation; Coupling with MS or ICP/MS instruments for research and development tasks; Schematic representation

ProfIC-Vario-01-AnCat

The Professional IC Vario system with sequential suppression,conductivity detection, and two analysis channels enables fully automatic determination of anions and cations, both in parallel and also completely independently of one another as a time-saving feature.Typical areas of application:Universal anion and cation analysis; Routine analysis with large numbers of samples without additional sample preparation; Schematic representation

ProfIC-Vario-01-UV-VIS

The Professional IC Vario system with UV/VIS detection enables fully automated determination of anions, cations, and organic compounds with optical absorption.Typical areas of application:Universal use for analysis of components that absorb UV or VIS light, respectively.; Routine analysis with large numbers of samples without additional sample preparation; Schematic representation

ProfIC-Vario-01-Amperometry

The Professional IC Vario system with amperometric detection enables fully automatic determination of sugar, oxidizable anions and additional oxidizable and reducible components.Typical areas of application:Universal use for analysis of oxidizable or reducible components; Routine analysis with large numbers of samples without additional sample preparation; Sugar analysis with pulsed amperometric detection (PAD); Trace analysis of cyanide and sulfide with direct amperometric detection (DC); Analysis of additional oxidizable or reducible anions; Determination of organic components with different potential forms (flexIPAD); Schematic representation

ProfIC-Vario-01-Anion-DR

The Professional IC Vario system with sequential suppression with Dosino regeneration of the suppressor and conductivity detection enables the fully automatic determination of anions or cations.Typical areas of application:Anion or cation analysis for universal application; Routine analysis with large numbers of samples without additional sample preparation; Coupling with MS or ICP/MS instruments for research and development tasks;

MATi 04

MATi 4 is a fully automated system for coulometric KF titrations with high sample throughput. Up to 160 samples in 6 mL vials can be placed on the sample rack of the Sample Processor. The sample is pipetted into an external coulometric cell and then titrated there. The system is controlled with the OMNIS software.

ProfIC-Vario-01-PCR-UV-VIS

The Professional IC Vario system with post-column derivatization and UV/VIS detection enables fully automated determination of anions, cations, and additional components that can be converted using post-column derivatization into products with optical absorption.Typical areas of application:Universal analysis with post-column derivatization and UV/VIS detection; Analysis with large numbers of samples without additional sample preparation; Trace analysis, e.g., of chromate, bromate, transition metals, etc.; Schematic representation

MATi 10

Fully automated system for volumetric Karl Fischer water content determination in up to 24 samples. The system is controlled with OMNIS software and consists of an 814 USB Sample Processor, a 901 Titrando and extensive accessories.The samples are weighed out into the beakers, sealed to protect against humidity and placed on the rack. Before the actual titration, they are dissolved in a defined volume of KF working medium, after which the water content is titrated.This method is particularly suitable for samples that dissolve readily in the KF working medium. In addition, solubility can be improved by using suitable solubility promoters.

MVA-25

Automated analysis system for the voltammetric determination of antioxidants in lubricants, including automatic sample preparation on the sample changer. Comprising 884 Professional VA, 858 Professional Sample Processor for antioxidants, 2x 800 Dosinos, 843 Pump Station, measuring head for rotating disk electrodes, and extensive accessories. For sample series of up to 24 samples.The viva software is required for control, data collection, and evaluation. PC, electrode set, and viva license need to be ordered separately.

MVA-20

Automated analysis system for the determination of organic additives in electroplating baths using CVS ("Cyclic Voltammetric Stripping"), CPVS ("Cyclic Pulse Voltammetric Stripping") and CP ("Chronopotentiometry"). Comprising 894 Professional CVS, 919 IC Autosampler plus, four 800 Dosinos, 843 Pump Station, measuring head for rotating disk electrodes and extensive accessories. For small sample series of up to 14 samples.The viva software is required for control, data recording and evaluation. PC, electrode set and viva license are to be ordered separately.

MATi-11

Fully automated system for volumetric Karl Fischer water content determination in up to 53 samples. This system is controlled with OMNIS software and consists of an 815 Robotic USB Sample Processor XL, a 901 Titrando, a Polytron PT 1300 D and extensive accessories.The samples are weighed out into beakers, sealed to protect against humidity and placed on the rack. Before the actual titration, a defined volume of KF reagent is added and the sample is pulverized with the help of a Polytron. The water that is released is titrated afterwards. Even samples of poor solubility, e.g., tablets, can be analyzed without difficulty with this method. The use of solubility promoters can be avoided in this way.

MVA-22

Automated analysis system for high-performance, flexible trace determinations with voltammetry and polarography with the Multi-Mode Electrode pro or the scTRACE Gold. Comprising 884 Professional VA for MME, 919 IC Autosampler plus for VA, two 800 Dosinos, 843 Pump Station, measuring head for rotating disk electrodes, and extensive accessories. For sample series of up to 28 samples.Determinations with rotating disc electrodes can also be performed with the MVA-22, e.g. determinations of organic additives in electroplating baths with "Cyclic Voltammetric Stripping" (CVS), "Cyclic Pulse Voltammetric Stripping" (CPVS), and chronopotentiometry (CP).The viva software is required for control, data acquisition, and evaluation. PC, electrode set, and viva license need to be ordered separately.

MVA-21

Automated analysis system for high-performance, flexible determination of organic additives in electroplating baths using "Cyclic Voltammetric Stripping" (CVS), "Cyclic Pulse Voltammetric Stripping" (CPVS) and chronopotentiometry (CP). Comprising 894 Professional CVS, 858 Professional Sample Processor, four 800 Dosinos, 843 Pump Station, measuring head for rotating disk electrodes and extensive accessories. For sample series of up to 56 samples.The viva software is required for control, data recording and evaluation. PC, electrode set and viva license are to be ordered separately.

MVA-23

Automated analysis system for the high-performance, flexible determination of organic additives in electroplating baths using CVS ("Cyclic Voltammetric Stripping"), CPVS ("Cyclic Pulse Voltammetric Stripping"), and chronopotentiometry (CP), or voltammetric heavy metal determinations with rotating disk electrodes. Comprising 884 Professional VA for CVS, 858 Professional Sample Processor, four 800 Dosinos, 843 Pump Station, measuring head for rotating disk electrodes. and extensive accessories. For sample series of up to 56 samples.The MVA-23 can also be used to perform voltammetric determinations with the Multi-Mode Electrode or the scTRACE Gold.The viva software is required for control, data acquisition, and evaluation. PC, electrode set, and viva license need to be ordered separately.

MVA-24

Automated analysis system for the high-performance, flexible determination of organic additives in electroplating baths using CVS ("Cyclic Voltammetric Stripping"), CPVS ("Cyclic Pulse Voltammetric Stripping"), and CP ("Chronopotentiometry"). Comprising 884 Professional VA for CVS, 858 Professional Sample Processor with Dosino for sample transfer, 4x additional 800 Dosinos for auxiliary solutions, 843 Pump Station, measuring head for rotating disk electrodes, and extensive accessories. For sample series of up to 112 samples.The viva software is required for control, data collection, and evaluation. PC, electrode set, and viva license need to be ordered separately.

2.919.0020

The 919 IC Autosampler plus fulfills the requirements of laboratories with medium sample numbers. It enables automation of the full range of Metrohm IC instruments.

MVA-03

MVA-03 is a fully automated analysis system for voltammetric trace analysis and education. This system is the optimum solution for the automatic investigation of small sample series that must be analyzed for one or two analytes in a single analysis run. The system is comprised of 797 VA Computrace, 863 Compact VA Autosampler and two 800 Dosinos for the automatic addition of standard solution and supporting electrolyte. Up to 18 samples can be investigated automatically, precisely and reproducibly.The system is supplied with extensive accessories for a complete measuring site setup, including VA Computrace software and electrodes: Multi-Mode Electrode pro (MME pro), Ag/AgCl reference electrode and Pt auxiliary electrode.

2.797.3110

The ideal solution for the completely automated determination of the concentration of the critical heavy metals in all types of water-vapor circulation in thermal power generating stations by means of voltammetry in small sample series. The 797 VA Computrace in combination with the 863 Compact VA Autosampler permits the automatic processing of up to 18 samples. The addition of auxiliary and standard solutions for calibration is accomplished with the aid of three dosing systems of the 800 Dosino type. An 843 Pump Station ensures carry-over-free analysis results, thanks to which the measuring vessel is rinsed after each sample. The system is the optimum solution for water samples in which one or two analytes are to be determined.Our promotion offer for orders placed by June 30, 2014: During the promotion period, Metrohm will give you an 800 Dosino for free, which makes the addition of auxiliary or standard solutions even more flexible, as well as an 827 pH Lab for measuring the pH value in your sample or for setting the pH value of the measurement solution as needed.

MVA-13

MVA-13 is an analysis system for the fully automated determination of organic additives in sample series of electroplating baths in routine laboratory work using the CVS technique ("Cyclic Voltammetric Stripping"). Up to 56 samples can be investigated with respect to suppressor content with the 838 Advanced VA Sample Processor. Up to 28 samples can be analyzed automatically during brightener determination. The possibility of recalibrating methods during a sample series guarantees the highest of accuracy. Comprised of 797 VA Computrace for CVS, 838 Advanced VA Sample Processor, three 800 Dosinos and rinsing equipment. The system is supplied with extensive accessories for a complete measuring site setup, including VA Computrace software and electrodes: rotating Pt disk electrode (RDE), Ag/AgCl reference electrode and Pt auxiliary electrode.

MVA-02

MVA-02 is a simple to operate, partially automated analysis system for voltammetric trace analysis and for education. For example, heavy metals can be conveniently determined in single samples without a sample changer. The system is comprised of the 797 VA Computrace with two 800 Dosinos for the automatic addition of standard solution and supporting electrolyte.The system is supplied with extensive accessories for a complete measuring site setup, including VA Computrace software and electrodes: Multi-Mode Electrode pro (MME pro), Ag/AgCl reference electrode and Pt auxiliary electrode.

MVA-12

MVA-12 is a partly automated analysis system for the manual determination of organic additives in single samples of electroplating baths in routine laboratory work using the CVS technique ("Cyclic Voltammetric Stripping"). Without a sample changer, it enables the convenient performance of determinations with a minimum of intervention on the part of the operating personnel. Comprised of 797 VA Computrace for CVS with three 800 Dosinos for the automatic addition of auxiliary solutions and sample.The system is supplied with extensive accessories for a complete measuring site setup, including VA Computrace software and electrodes: rotating Pt disk electrode (RDE), Ag/AgCl reference electrode and Pt auxiliary electrode.

ProfIC-01-Anion

The Professional IC system with sequential suppression and conductivity detection enables the fully automatic determination of anions. "ProfIC 1" enables the safe management of all routine tasks in ion chromatography. It is simple to use and exceptionally reliable. Schematic diagram

ProfIC-01-Cation

Professional IC system with conductivity detection enables the fully automatic determination of cations and anions (non-suppressed). "ProfIC 1" enables the safe management of all routine tasks in ion chromatography. It is simple to use and exceptionally reliable. Schematic diagram

ProfIC-01-AnCat

The very compact Professional IC system with conductivity detection enables the fully automatic determination of anions and cations. With "ProfIC 1 – AnCat", anions and cations can be determined not only in parallel but also in time-saving fashion completely independently of one another. Both of the systems integrated in "ProfIC 1 – AnCat" use the same 858 Professional Sample Processor with pump that is subjected to intelligent management by the MagIC Net™ software. Schematic diagram

2.889.0010

The 889 IC Sample Center is a robust Autosampler for high sample throughput, optimized for the challenges of the modern analytic laboratory. It works in accordance with the x-y-z principle and a syringe control with high resolution for precise sample injection. A double needle system enables the penetration of vessel caps and septa. A PEEK injection valve completes the automation system of the 889 IC Sample Center. It is the appropriate automation solution when you have only a very small amount of sample.

2.863.0010

The 863 Compact IC Autosampler is the ideal help for routine analysis. It enables automation of the full range of Metrohm IC instruments.

2.889.0020

The 889 IC Sample Center – cool is the appropriate automation solution when you have only a very small amount of sample. In comparison with the 889 IC Sample Center, it possesses in addition a cooling function and is thus the ideal sample changer for biochemically relevant or thermally unstable samples.

2.855.0020

Basic model for setting up customer-specific automation in the titration. Space-saving Robotic Sample Processor XL with integrated Titrando, one workstation including Swing Head and two built-in membrane pumps. The programming of the methods is accomplished by means of the handy Touch Control or with the tiamo™ titration software or OMNIS Software.

2.855.0010

Basic model for setting up customer-specific automation in the titration. Space-saving Robotic Sample Processor XL with integrated Titrando, one workstation including Swing Head and one built-in membrane pump. Either an external peristaltic pump or membrane pump can be connected for aspiration of the titrated solution (optional). The programming of the methods is accomplished by means of the handy Touch Control or with the tiamo™ titration software or OMNIS Software.

2.855.0040

Entry-level model of the Robotic Titrosampler for medium sample throughput. The space-saving Robotic Sample Processor XL with integrated Titrando, one workstation and two built-in membrane pumps is expanded for application-specific automation in titration through the selection of sample rack and electrode. The programming of the methods is accomplished by means of the handy Touch Control or with the tiamo™ titration software or OMNIS Software.With increasing sample throughputs, the Robotic Titrosampler "Light" can be expanded simply and inexpensively to become the "Basic" model with which many times the original sample quantity can be managed.

2.889.0040

The 889 IC Sample Center Basic – cool is the appropriate automation solution when you have only a very small amount of sample. In comparison with the 889 IC Sample Center Basic, it possesses in addition a cooling function and is thus the ideal sample changer for biochemically relevant or thermally unstable samples.The sample transfer takes place either with a peristaltic pump in the IC system or with an 800 Dosino, e.g. when applying the intelligent Partial Loop Injection Technique.Supported with MagIC Net 4.1 and higher.

2.855.0030

Entry-level model of the Robotic Titrosampler for medium sample throughput. The space-saving Robotic Sample Processor XL with integrated Titrando, one workstation, and one built-in membrane pump is expanded for application-specific automation in titration through the selection of sample rack and electrode. Either an external peristaltic pump or membrane pump can be connected for aspiration of the titrated solution (optional). The programming of the methods is accomplished by means of the handy Touch Control or with the tiamo™ titration software or OMNIS Software. With increasing sample throughputs, the Robotic Titrosampler "Light" can be expanded simply and inexpensively to become the "Basic" model with which many times the original sample quantity can be managed.

2.843.0240

The 843 Membrane Pump Station enables the automatic rinsing and emptying of the measuring vessel in partly automated and fully automated Professional VA and CVS systems. It has two built-in membrane pumps that can be controlled via the remote signal.The versions for VA and CVS are equipped with the complete accessories for the automatic rinsing and emptying of the measuring vessel.

2.843.0230

The 843 Peristaltic Pump Station enables the automatic rinsing and emptying of the measuring vessel in partly automated and fully automated Professional VA and CVS systems. It has 2 built-in peristaltic pumps that can be controlled via the remote signal.The versions for VA and CVS are equipped with the complete accessories for the automatic rinsing and emptying of the measuring vessel. The connection cable must be ordered separately.

2.848.0010

Compact titrator for dynamic (DET) titrations with automatic equivalence point finding; monotonic (MET) titrations with automatic equivalence point finding; endpoint titrations (SET);

2.862.0010

The 862 Compact Titrosampler – titrator and sample changer in one – is a completely automated titration station with the support surface of a commercially available analytical balance.Compact and economical instrument for the automatic performance of dynamic (DET) and monotonic (MET) titrations with automatic equivalence point finding and endpoint titrations (SET) in a very small space. Various titrations can be performed fully automatically and the electrodes can be cleaned and stored in a total of 12 positions. The titration curve is directly in view thanks to the large, clearly organized Live Display and the current status of the sample series is recognizable at once. Pressing samples can be given priority analysis at any time.

2.862.2010

The 862 Salt Compact Titrosampler is just the right choice for the automatic performance of potentiometric chloride analyses in a wide variety of samples.The combination of titrator and sample changer in a single instrument that offers the automatic performance of dynamic (DET) and monotonic (MET) titrations with automatic equivalence point finding and endpoint titrations (SET) in a very small space. Equipped with extensive accessories, the 862 Salt Compact Titrosampler is ready for immediate use.Various titrations can be performed fully automatically and the electrodes can be cleaned and stored in a total of 12 positions. The titration curve is directly in view thanks to the large, clearly organized Live Display and the current status of the sample series is recognizable at once. Pressing samples can be given priority analysis at any time.

2.862.1010

The 862 Food/Beverage Compact Titrosampler is just the right choice for the automatic performance of potentiometric analyses required in the food industry.The combination of titrator and sample changer in a single instrument that offers the automatic performance of dynamic (DET) and monotonic (MET) titrations with automatic equivalence point finding and endpoint titrations (SET) in a very small space. Equipped with extensive accessories, the 862 Food/Beverage Compact Titrosampler is ready for immediate use.Various titrations can be performed fully automatically and the electrodes can be cleaned and stored in a total of 12 positions. The titration curve is directly in view thanks to the large, clearly organized Live Display and the current status of the sample series is recognizable at once. Pressing samples can be given priority analysis at any time.

2.1024.0020

Module for installation in the OMNIS Sample Robot WSM. This module contains a workstation for the automatic processing of sample vessels and two pumps for the automatic cleaning (rinsing and extraction) of sample vessels and sensors. The workstation takes up the sample beaker for the analysis. Used sensors can be cleaned or parked in the storage beaker of the workstation between analyses. If stirring is required during the analysis, then a separate rod stirrer or a magnetic stirrer can be installed for this workstation.

2.1024.0030

Module for installation in the OMNIS Sample Robot WSM. This module contains 2 workstations for the automatic processing of sample vessels and 4 pumps for the automatic cleaning of sample vessels and sensors (rinsing and extraction) at both workstations. The workstations take up the sample beaker for the analysis. Used sensors can be cleaned or parked in the storage beakers of the workstations between analyses. If stirring is required during the analysis, then a separate rod stirrer or a magnetic stirrer can be installed for each workstation.

2.858.0120

The 858 Professional Sample Processor CVS with Dosino for sample transfer, in conjunction with Professional VA/CVS instruments and viva, enables the fully automatic processing of large sample series of organic additives in electroplating baths, e.g. brighteners, and suppressors, using "Cyclic Voltammetric Stripping" (CVS). The system is controlled directly by the viva software and permits automatic changes of method between different determination types. The sample rack (supplied) holds 56 samples of a maximum of 11 mL for suppressor determination and 28 samples of a maximum of 50 mL for brightener determination. A Dosino is used for sample transfer into the measuring vessel. This enables reduction and automatic measurement of the sample amount required.The 858 Professional Sample Processor CVS with Dosino for sample transfer is supplied with built-in robotic arm, together with accessories, Dosino, sample rack, and connection cable for setting up a complete workplace, although it does not come with rinsing equipment.

2.874.0120

The 874 Oven Sample Processor is used for automatic thermal sample preparation in Karl Fischer titration. The oven method is particularly suitable for samples that do not release their water until higher temperatures have been reached, for sparingly soluble samples, or those that react with the KF reagent.

2.855.3020

The complete package for the determination of acids and/or bases for very high sample numbers contains all the components for a fully automatic acid-base titration in the smallest possible space in a minimum of time. Instruments, accessories, software, and application know-how – simply everything is included.

2.810.0010

Sample Processor for the automated analysis of routine samples using 916 Ti-Touch or 915 KF Ti-Touch.Sample Processor with one workstation and one built-in membrane pump for the automatic processing of potentiometric as well as Karl Fischer titrations, in series with small to medium quantities. In addition to the built-in pump, an additional one (membrane or peristaltic) and up to three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.

2.855.1010

The complete package for the determination of chloride contains all the components for a fully automatic chloride titration in the smallest possible space in a minimum of time. Instruments, accessories, software, and application know-how – simply everything is included.

2.855.2020

The complete package for the determination of fluoride contains all the components for a fully automatic fluoride determination in the smallest possible space in a minimum of time. Instruments, accessories, software, and application know-how – simply everything is included.

2.858.0130

The 858 Professional Sample Processor VA for antioxidants enables the fully automatic processing of sample series of lubricants for determining the concentration of antioxidants in combination with Professional VA instruments and viva. The system is controlled directly with the viva software. The sample rack (supplied) holds 24 samples, which are extracted automatically on the sample changer for sample preparation prior to determination.The 858 Professional CVS Sample Processor VA for antioxidants is supplied with built-in robotic arm, together with accessories, sample rack, magnetic stirrer, and connection cable for setting up a complete workplace, although it does not come with rinsing equipment.

2.919.0130

The 919 IC Autosampler plus for VA is suitable for small sample series of fully automatic trace determinations of heavy metals using polarography and voltammetry together with Professional VA instruments and viva. The system is controlled directly by the viva software and permits automatic changes of method between different types of determinations. The sample rack supplied holds 28 samples with a maximum size of 10 mL.The 919 IC Autosampler plus for VA is supplied with accessories, sample rack, and connection cable so you can set up a complete workplace, although it does not come with rinsing equipment.

2.855.1020

The complete package for the determination of acids and/or bases contains all the components for a fully automatic acid-base titration in the smallest possible space in a minimum of time. Instruments, accessories, software, and application know-how – simply everything is included.

2.855.2010

The complete package for the determination of TAN and/or TBN contains all the components for a fully automatic TAN/TBN titration in the smallest possible space in a minimum of time. Instruments, accessories, software, and application know-how – simply everything is included.

2.919.0120

The 919 IC Autosampler plus for CVS, in conjunction with Professional VA/CVS instruments and viva, is suitable for small sample series of fully automatic determinations of organic additives in electroplating bath, e.g. "brighteners" and "suppressors" using "Cyclic Voltammetric Stripping" (CVS). The system is controlled directly by the viva software and permits automatic changes of method between different types of determinations. The sample rack supplied holds 14 samples with a maximum size of 50 mL.The 919 IC Autosampler plus for CVS is supplied with accessories, sample rack, and connection cable so you can set up a complete workplace, although it does not come with rinsing equipment.

2.877.0010

Compact titrator for potentiometric endpoint titrations (SET); monotonic titrations with automatic equivalence point finding (MET);

ProfIC-Vario-12-Anion

The Professional IC Vario system with automatic calibration, Dosino Regeneration,automatic eluent production, sequential suppression and conductivity detection enables the online determination of anions or cations from various sample flows. The system is optimized for uninterrupted use (24/7).Typical areas of application:Continuous analysis of processes; Monitoring of drinking and surface water; Monitoring of cooling water; Trace analysis; Schematic representation

2.858.0110

The 858 Professional Sample Processor for VA and CVS, in conjunction with Professional VA/CVS instruments and viva, enables the fully automatic processing of large sample series of organic additives in electroplating baths, e.g. "brighteners" and "suppressors" using "Cyclic Voltammetric Stripping" (CVS). The system is controlled directly by the viva software and permits automatic changes of method between different types of determinations. The sample rack supplied holds 56 samples of a maximum of 11 mL and 28 samples of a maximum of 50 mL for brightener determination. The 858 Professional Sample Processor for VA and CVS is supplied with built-in robotic arm, together with accessories, sample rack and connection cable for setting up a complete workplace, although it does not come with rinsing equipment.

2.874.0130

The 874 Oven Sample Processor is used for automatic thermal sample preparation in Karl Fischer titration. The oven method is particularly suitable for samples that do not release their water until higher temperatures have been reached, for sparingly soluble samples, or those that react with the KF reagent.This instrument can be modified to match customer-specific sample vessels. Please contact your Metrohm representative for further information.

2.941.0010

The 941 Eluent Production Module enables the automatic production of an eluent. It enables continuous working without manual intervention and guarantees stable retention times. It can be combined with all Metrohm IC instruments and is monitored by MagIC Net.

2.814.0030

USB Sample Processor with one workstation for the automatic processing of routine samples in series with small to medium quantities. Up to two pumps (membrane or peristaltic) and three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

2.1073.0010

OMNIS Sample Robot S – NIR for the direct transition to fully automated spectroscopy. The system provides space for 1 sample rack for up to 77 vials with diameters of 8–28 mm.The OMNIS Sample Robot S – NIR supports the analyses of both liquid and solid samples.

2.1074.0010

OMNIS Sample Robot M – NIR for the direct transition to fully automated spectroscopy. The system provides space for 3 sample racks for up to 231 vials with diameters of 8–28 mm.The OMNIS Sample Robot M – NIR supports the analyses of both liquid and solid samples.

2.814.0020

USB Sample Processor with one workstation and two built-in membrane pumps for the automatic processing of routine samples in series with small to medium quantities. In addition to the built-in pumps, up to three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately. The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

2.815.0020

Robotic USB Sample Processor XL with one workstation and two built-in membrane pumps for the automatic processing of routine samples in series with large quantities and for complex sample preparation or parallel runs. Up to three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, robotic arm, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

2.815.0030

Robotic USB Sample Processor XL with one workstation for the automatic processing of routine samples in series with large quantities and for complex sample preparation or parallel runs. Up to two pumps (membrane or peristaltic) and three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, robotic arm, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

ProfIC-Vario-04-Cation

The Professional IC Vario system with Metrohm's intelligent Inline Dilution and conductivity detection enables fully automatic determination of cations or anions (non-suppressed) in concentrated solutions.Typical areas of application:Samples with high ion concentration; Samples from all industries; Schematic representation

ProfIC-Vario-02-Cation

The Professional IC Vario system with Metrohm inline ultrafiltration and conductivity detection enables fully automatic determination of cations or anions (non-suppressed).Typical areas of application:Samples with slight to moderate contamination with particles, algae, or bacteria; Drinking and surface water; Process and waste water; Schematic representation

2.814.0010

USB Sample Processor with one workstation and one built-in membrane pump for the automatic processing of routine samples in series with small to medium quantities. In addition to the built-in pump, an additional one (membrane or peristaltic) and up to three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

ProfIC-Vario-04-Anion

The Professional IC Vario system with Metrohm's intelligent Inline Dilution, sequential suppression, and conductivity detection enables fully automatic determination of anions or cations in concentrated solutions.Typical areas of application:Samples with high ion concentration; Samples from all industries; Schematic representation

ProfIC-Vario-02-Anion

The Professional IC Vario system with Metrohm Inline Ultrafiltration, sequential suppression, and conductivity detection enables fully automatic determination of anions or cations.Typical areas of application:Samples with slight to moderate contamination with particles, algae, or bacteria; Drinking and surface water; Process and waste water; Schematic representation

2.948.0010

Automated hydroxide eluent production takes place with the 948 Continuous IC Module. Isocratic eluents can be produced and gradients can be run.The 948 Continuous IC Module, CEP is comprised of the following parts:948 Continuous IC Module; Eluent Producer Cartridge (EPC, 6.02850.200); Continuous anion trap (CT, 6.02850.100); High-pressure degasser (H-DEG, 6.02850.000); Example methods according to 948 Continuous IC Module manual.

2.1030.1020

OMNIS Sample Robot Oven with 2 oven modules 6 mL and extensive accessories for the direct transition to fully automated thermal sample preparation with subsequent water determination in accordance with Karl Fischer. The system provides space in 2 sample racks for 100 sample beakers of 6 mL each. This modular system is supplied completely installed and can thus be put into operation in a very short time.

ProfIC-Vario-04-AnCat

The Professional IC Vario system with Metrohm's intelligent Inline Dilution, sequential suppression, and conductivity detection enables fully automatic determination of anions and cations in concentrated solutions.Typical areas of application:Samples with high ion concentration; Samples from all industries; Schematic representation

2.815.1110

The 815 Robotic Titration is a system for the completely automatic preparation of solid samples that need to be reduced and placed in solution prior to titration.The system consists of:1 x 815 Robotic USB Sample Processor XL1 x 136 Polytron with power supply unit2 x 772 Pump Unit2 x 786 Swing Head1 x 802 Rod stirrer

2.815.0010

Robotic USB Sample Processor XL with one workstation and one built-in membrane pump for the automatic processing of routine samples in series with large quantities and for complex sample preparation or parallel runs. In addition to the built-in pump, an additional one (membrane or peristaltic) and up to three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, robotic arm, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

ProfIC-Vario-02-AnCat

The Professional IC Vario system with Metrohm inline ultrafiltration, sequential suppression and conductivity detection enables fully automatic determination of anions and cations.Typical areas of application:Samples with slight to moderate contamination with particles, algae, or bacteria; Drinking and surface water; Process and waste water; Schematic representation

2.815.3110

The 815 Robotic Filtration Soliprep is a complete system for the completely automatic preparation of samples which need to be homogenized and filtered prior to their determination.The system consists of:1 x 815 Robotic USB Sample Processor XL1 x 136 Polytron with power supply unit1 x 772 Pump Unit1 x 786 Swing Head1 x reinforced 786 Swing Head1 x 800 Dosino

2.1024.0010

Module for installation in the OMNIS Sample Robot WSM. This module contains a workstation for the automatic processing of sample vessels without pumps. The workstation takes up the sample beaker for the analysis. Used sensors can be cleaned or parked in the storage beaker of the workstation between analyses. If stirring is required during the analysis, then a separate rod stirrer or a magnetic stirrer can be attached for this workstation.

ProfIC-Vario-06-Cation

The Professional IC Vario system with Metrohm Inline Dilution, Metrohm Inline Ultrafiltration and conductivity detection enables fully automatic determination of cations or anions (non-suppressed) that are present in very high concentrations and that have matrices containing particles.Typical areas of application:Rinse, process, and waste water; Extractions and digestion solutions; Food samples; Schematic representation

ProfIC-Vario-03-Cation

The Professional IC Vario system with Metrohm inline dialysis and conductivity detection enables fully automatic determination of cations or anions (non-suppressed).Typical areas of application:Samples heavily contaminated with particles, algae or bacteria; Process, wash, and waste water; Emulsions, dispersions, cutting oils and samples containing petroleum; Milk products and other samples containing protein; Schematic representationInstallation instructions

ProfIC-Vario-07-Cation

The Professional IC Vario system with Metrohm Inline Dilution, Inline Dialysis and conductivity detection enables the fully automated determination of cations or anions (non-suppressed) that are present in high concentrations and in difficult matrices.Typical areas of application:Process, wash and waste water; Samples containing oil; Inline Extraction for biodiesel analysis; Schematic representation

2.864.1130

The Robotic Balance Sample Processor TAN/TBN offers the rapid and convenient preparation and analysis of petrochemical products in a single system.An aliquot of the sample is fully automatically weighed into the titration beaker and diluted with solvent, after which titration is used to determine the TAN and/or TBN value. After analysis, the titration beaker is emptied and the electrode is cleaned and conditioned. Traceability is ensured by the direct preparation on the Balance Sample Processor and the danger of mixing up externally prepared samples is eliminated.The entire system is monitored with the proven titration and control software tiamo™, the database of which documents each preparation step (including sample size) and the titration results, clearly and separately for each sample.

2.814.0120

USB Sample Processor with two workstations and four built-in membrane pumps for the automatic processing of routine samples in series with small to medium quantities. In addition to the built-in pumps, up to three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

2.815.0120

Robotic USB Sample Processor XL with two workstations and four built-in membrane pumps for the automatic processing of routine samples in series with large quantities and for complex sample preparation or parallel runs. Up to three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, robotic arm, Swing Head, and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

ProfIC-Vario-06-Anion

The Professional IC Vario system with Metrohm Inline Dilution, Metrohm Inline Ultrafiltration, sequential suppression and conductivity detection enables fully automatic determination of anions or cations that are present in very high concentrations and that have matrices containing particles.Typical areas of application:Rinse, process, and waste water; Extractions and digestion solutions; Food samples; Schematic representation

ProfIC-Vario-03-Anion

The Professional IC Vario system with Metrohm Inline Ultrafiltration, sequential suppression, and conductivity detection enables fully automatic determination of anions or cations.Typical areas of application:Samples heavily contaminated with particles, algae or bacteria; Process, wash, and waste water; Emulsions, dispersions, cutting oils and samples containing petroleum; Milk products and other samples containing protein; Schematic representation

2.1012.1010

OMNIS Sample Robot L with a "Peristaltic" (4-channel) pump module and a Pick&Place module in addition to extensive accessories for the direct transition to fully automatic titration. The system provides space in seven sample racks for 112 sample beakers of 120 mL each.The system can be extended upon request to include up to four peristaltic pumps and three additional Pick&Place modules, thus quadrupling the throughput while at the same time also guaranteeing long and interruption-free operation.

2.814.0110

USB Sample Processor with two workstations and two built-in membrane pumps for the automatic processing of routine samples in series with small to medium quantities. In addition to the built-in pumps, two additional pumps (membrane or peristaltic) and up to three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

ProfIC-Vario-07-Anion

The Professional IC Vario system with Metrohm Inline Dilution, Inline Dialysis, sequential suppression and conductivity detection enables the fully automatic determination of anions or cations that are present in high concentrations and in difficult matrices.Typical areas of application:Process, wash and waste water; Samples containing oil; Inline Extraction for biodiesel analysis; Schematic representation

2.814.0130

USB Sample Processor with two workstations for the automatic processing of routine samples in series with small to medium quantities. Up to four pumps (membrane or peristaltic) and three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

ProfIC-Vario-06-AnCat

The Professional IC Vario system with Metrohm Inline Dilution, Metrohm Inline Ultrafiltration, sequential suppression, and conductivity detection enables fully automatic determination of anions and cations that are present in very high concentrations and that have matrices containing particles.Typical areas of application:Rinse, process, and waste water; Extractions and digestion solutions; Food samples; Schematic representation

ProfIC-Vario-05-Cation

The Professional IC Vario system with Metrohm's intelligent inline sample preconcentration and conductivity detection enables fully automatic determination of cations or anions (non-suppressed) in solutions with low ion concentration.Typical areas of application:Numerous applications, ranging from ultrapure water analysis to drinking water analysis; Analyses of different samples from power plants; Process control and monitoring of rinsing solutions, e.g., in the semiconductor industry; Schematic representationInstallation instructions

2.1030.1010

OMNIS Sample Robot Oven with 1 oven module 6 mL and extensive accessories for the direct transition to fully automated thermal sample preparation with subsequent water determination in accordance with Karl Fischer. The system provides space in 2 sample racks for 100 sample beakers of 6 mL each. This modular system is supplied completely installed and can thus be put into operation in a very short time. The system can also be extended upon request to include an additional oven module, thus doubling the throughput.

2.1030.1030

OMNIS Sample Robot Oven with 1 oven module 8 mL and extensive accessories for the direct transition to fully automated thermal sample preparation with subsequent water determination in accordance with Karl Fischer. The system provides space in 2 sample racks for 100 sample beakers of 8 mL each. This modular system is supplied completely installed and can thus be put into operation in a very short time. The system can also be extended upon request to include an additional oven module, thus doubling the throughput.

ProfIC-Vario-15-Cation

The Professional IC Vario system with Metrohm's intelligent Partial Loop Injection Technique and conductivity detection enables fully automatic determination of cations or anions (non-suppressed). "Partial Loop Injection" enables the injection of various sample volumes.Typical areas of application:Universal use for all types of samples; From trace analysis to waste water analysis; Great differences in concentration in a single sample series; Schematic representationInstallation instructions

ProfIC-Vario-05-Anion

The Professional IC Vario system with Metrohm's intelligent inline sample preconcentration, sequential suppression, and conductivity detection enables fully automatic determination of anions or cations in solutions with low ion concentration.Typical areas of application:Numerous applications, ranging from ultrapure water analysis to drinking water analysis; Analyses of different samples from power plants; Process control and monitoring of rinsing solutions, e.g., in the semiconductor industry; Schematic representationInstallation instructions

ProfIC-Vario-15-Anion

The Professional IC Vario system with Metrohm's intelligent Partial Loop Injection Technique, sequential suppression and conductivity detection enables fully automated determination of anions or cations. "Partial Loop Injection" enables the injection of various sample volumes.Typical areas of application:Universal use for all types of samples; From trace analysis to waste water analysis; Great differences in concentration in a single sample series; Schematic representationInstallation instructions

2.815.0110

Robotic USB Sample Processor XL with two workstations and two built-in membrane pumps for the automatic processing of routine samples in series with large quantities and for complex sample preparation or parallel runs. In addition to the built-in pumps, up to two additional pumps (membrane or peristaltic) and three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, robotic arm, Swing Head and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

2.815.4110

The 815 Robotic Soliprep for LC is a complete system for the completely automatic preparation of samples which need to be dissolved, homogenized, diluted or filtered prior to their determination. The samples are conveyed directly into the injector of the chromatograph after preparation.Comprised of:1 x 815 Robotic USB Sample Processor XL1 x 136 Polytron with power supply1 x 772 Pump Unit 2 x 786 Swing Head2 x 800 Dosino

ProfIC-Vario-15-AnCat

The Professional IC Vario system with Metrohm's intelligent Partial Loop Injection Technique, sequential suppression, and conductivity detection enables fully automated determination of anions and cations. "Partial Loop Injection" enables the injection of various sample volumes.Typical areas of application:Universal use for all types of samples; From trace analysis to waste water analysis; Great differences in concentration in a single sample series; Schematic representationInstallation instructions

2.815.0130

Robotic USB Sample Processor XL for the automatic processing of routine samples in series with large quantities and for complex sample preparation or parallel runs. Up to four pumps (membrane or peristaltic) and three dosing devices for Liquid Handling tasks can be connected.Because of the multitude of application variants, rack, stirrer, titration head, robotic arm, Swing Head, and sample vessels must be tailored to the application and ordered separately.The control is "stand alone" using Touch Control. The following software products can be selected for the PC control: tiamo™ titration software, MagIC Net chromatography software, viva voltammetry software, or OMNIS.

ProfIC-Vario-05-AnCat

The Professional IC Vario system with Metrohm's intelligent inline sample preconcentration, sequential suppression and conductivity detection enables fully automatic determination of anions and cations in solutions with low ion concentration.Typical areas of application:Numerous applications, ranging from ultrapure water analysis to drinking water analysis; Analyses of different samples from power plants; Process control and monitoring of rinsing solutions, e.g., in the semiconductor industry; Trace analysis in snow and ice; Schematic representationInstallation instructions

2.1011.1010

OMNIS Sample Robot M with a "Peristaltic" (4-channel) pump module and a Pick&Place module in addition to extensive accessories for the direct transition to fully automatic titration. The system provides space in five sample racks for 80 sample beakers of 120 mL each.The system can be extended upon request to include up to four peristaltic pumps and three additional Pick&Place modules, thus quadrupling the throughput. If even more samples are to be placed on the Sample Robot, then this Sample Robot can be expanded to become an L-sized OMNIS Sample Robot, thus enabling 112 samples to be processed in parallel on up to four Pick&Place modules and thus guaranteeing long and interruption-free operation.

2.855.1030

The Robotic Analyzer Light package contains all the components for a fully automated titration or measurement in the smallest possible space in a minimum of time.In addition to the Robotic Titrosampler Basic with a rack for 22 samples in 120 mL PP beakers, the package also includes a rod stirrer, a peristaltic pump and a Dosino with 20 mL dosing unit and the OMNIS control software.Only electrode cables, sensors and additional dosing devices as needed must be added, so that it will be available for flexible use as Acid-Base, TAN/TBN, Chloride or Fluoride Analyzer.Should the number of samples increase, then the option also exists of expanding the system to the Robotic Analyzer Basic.

2.1010.1010

OMNIS Sample Robot S with a "Peristaltic" (2-channel) pump module and a Pick&Place module in addition to extensive accessories for the direct transition to fully automatic titration. The system provides space in two sample racks for 32 sample beakers of 120 mL each. This modular system is supplied completely installed and can thus be put into operation in a very short time.The system can also be extended upon request to include two additional peristaltic pumps and another Pick&Place module, thus doubling the throughput. If additional workstations are required, then this Sample Robot is already able to be expanded to become an L-sized OMNIS Sample Robot, thus enabling samples from seven racks to be processed in parallel on up to four Pick&Place modules and quadrupling the sample throughput.

2.1030.0010

Main module for setting up an OMNIS Sample Robot Oven in size S. This module is equipped with the module and rack plate. It is already equipped with the main lift and a gripper. It must be equipped with sample racks and at least 1 oven module in order to use it to set up a functioning Sample Robot Oven.

2.894.1210

894 Professional CVS semiautomated is a convenient, high-end routine analyzer for the determination of organic additives in electroplating baths using "Cyclic Voltammetric Stripping" (CVS), "Cyclic Pulse Voltammetric Stripping" (CPVS) and Chronopotentiometry (CP). The proven Metrohm electrode methods combined with a high-performance potentiostat/galvanostat and the extremely flexible viva software open up new perspectives in CVS. The replaceable measuring head enables rapid changes between various applications with different electrodes. The potentiostat with a certified calibrator readjusts itself automatically before each measurement, thus guaranteeing maximum precision. The integrated temperature measurement input allows you to monitor the solution temperature during the measurement.2x 800 Dosinos (supplied) permit the automatic addition of auxiliary solutions during the determination, e.g., VMS, standard solutions or samples for the Dilution Titration technique (DT). The viva software is required for control, data collection, and evaluation.The 894 Professional CVS semiautomated is supplied with extensive accessories and measuring head for rotating disk electrodes. Electrode set and viva license need to be ordered separately.

2.894.1310

894 Professional CVS semiautomated is a convenient, high-end routine analyzer for the determination of organic additives in electroplating baths using "Cyclic Voltammetric Stripping" (CVS), "Cyclic Pulse Voltammetric Stripping" (CPVS) and Chronopotentiometry (CP). The proven Metrohm electrode methods combined with a high-performance potentiostat/galvanostat and the extremely flexible viva software open up new perspectives in CVS. The replaceable measuring head enables rapid changes between various applications with different electrodes. The potentiostat with a certified calibrator readjusts itself automatically before each measurement, thus guaranteeing maximum precision. The integrated temperature measurement input allows you to monitor the solution temperature during the measurement.3x 800 Dosinos (supplied) permit the automatic addition of auxiliary solutions during the determination, e.g., VMS, standard solutions or samples for the Dilution Titration technique (DT).The viva software is required for control, data collection, and evaluation.The 894 Professional CVS semiautomated is supplied with extensive accessories and measuring head for rotating disk electrodes. Electrode set and viva license need to be ordered separately.

2.884.1210

884 Professional VA semiautomated for CVS applications is a convenient high-end routine analyzer for determinations of organic additives in electroplating baths with "Cyclic Voltammetric Stripping" (CVS), "Cyclic Pulse Voltammetric Stripping" (CPVS), and chronopotentiometry (CP), or voltammetric heavy metal determinations with rotating disk electrodes. The proven Metrohm electrode methods combined with a high-performance potentiostat/galvanostat and the extremely flexible viva software open up new perspectives in CVS. The potentiostat with a certified calibrator readjusts itself automatically before each measurement, thus guaranteeing maximum precision. The integrated temperature measurement input allows you to monitor the solution temperature during the measurement.The instrument can also be used to perform voltammetric determinations. The replaceable measuring head enables rapid changes between the various applications with different electrodes.2x 800 Dosinos (supplied) permit the automatic addition of auxiliary solutions during the determination, e.g., VMS, standard solutions or samples for the Dilution Titration technique (DT).The viva software is required for control, data collection, and evaluation.The 884 Professional VA semiautomated for CVS applications is supplied with extensive accessories and a measuring head for rotating disk electrodes. Electrode set and viva license need to be ordered separately.

2.884.1310

884 Professional VA semiautomated for CVS applications is a convenient high-end routine analyzer for determinations of organic additives in electroplating baths with "Cyclic Voltammetric Stripping" (CVS), "Cyclic Pulse Voltammetric Stripping" (CPVS), and chronopotentiometry (CP), or voltammetric heavy metal determinations with rotating disk electrodes. The proven Metrohm electrode methods combined with a high-performance potentiostat/galvanostat and the extremely flexible viva software open up new perspectives in CVS. The potentiostat with a certified calibrator readjusts itself automatically before each measurement, thus guaranteeing maximum precision. The integrated temperature measurement input allows you to monitor the solution temperature during the measurement.The instrument can also be used to perform voltammetric determinations. The replaceable measuring head enables rapid changes between the various applications with different electrodes.3x 800 Dosinos (supplied) permit the automatic addition of auxiliary solutions during the determination, e.g., VMS, standard solutions or samples for the Dilution Titration technique (DT).The viva software is required for control, data collection, and evaluation.The 884 Professional VA semiautomated for CVS applications is supplied with extensive accessories and a measuring head for rotating disk electrodes. Electrode set and viva license need to be ordered separately.

2.884.1110

884 Professional VA semiautomated for Multi-Mode Electrode (MME) is a convenient high-end routine analyzer for trace determinations with voltammetry and polarography with the Multi-Mode Electrode pro or the scTRACE Gold. The proven Metrohm electrode methods in combination with a high-performance potentiostat/galvanostat and the extremely flexible viva software open up new perspectives for the determination of heavy metals. The potentiostat with a certified calibrator readjusts itself automatically before each measurement, thus guaranteeing maximum precision.Determinations with rotating disc electrodes can also be performed with the instrument, e.g. determinations of organic additives in electroplating baths with "Cyclic Voltammetric Stripping" (CVS), "Cyclic Pulse Voltammetric Stripping" (CPVS), and chronopotentiometry (CP). The replaceable measuring head enables rapid changes between the various applications with different electrodes.2x 800 Dosinos (supplied) permit the automatic addition of auxiliary solutions during the determination, e.g., electrolyte, buffer or standard solutions.The viva software is required for control, data collection, and evaluation.The 884 Professional VA semiautomated for Multi-Mode Electrode (MME) is supplied with extensive accessories and a measuring head for the Multi-Mode Electrode pro. Electrode set and viva license need to be ordered separately.

2.858.0010

The 858 Professional Sample Processor processes samples from 500 µL to 500 mL. The sample transfer takes place either by means of a peristaltic pump on the 850 Professional IC system or with an 800 Dosino.

2.1014.0010

Module for installation in the module plate of the Pick&Place of the OMNIS Sample Robot. This workstation takes up the sample beaker for the analysis. Used sensors are cleaned or parked in the storage beaker of the Pick&Place module between analyses. If stirring is required during the analysis, then a separate rod stirrer must be used for this workstation.

2.858.0020

The 858 Professional Sample Processor – Pump processes samples from 500 µL to 500 mL. The sample transfer takes place either with the installed bidirectional two-channel peristaltic pump or with an 800 Dosino.

2.1014.0110

Module for installation in the module plate of the Pick&Place of the OMNIS Sample Robot. This workstation takes up the sample beaker for the analysis. The built-in magnetic stirrer makes it possible to analyze samples that were prepared externally on a magnetic agitator directly in the Sample Robot without having to remove the magnetic stirring bar beforehand. Used sensors are cleaned or parked in the storage beaker of the Pick&Place module between analyses.

2.1016.0010

Module for installation in the module plate of the Pick&Place of the OMNIS Sample Robot. This workstation is equipped with both a rinsing pump and an aspiration pump. They are used to clean the sensors in a Pick&Place module and to empty the sample beaker after the analysis before it is returned to the rack once again.

2.885.0010

The 885 Compact Oven Sample Changer is used for thermal sample preparation in Karl Fischer titration. In the oven the samples can be heated up to 250°C. The moisture contained in the sample evaporates and is transported by a dry carrier gas into the titration cell, where the analysis takes place.

2.1016.0110

Module for installation in the module plate of the Pick&Place of the OMNIS Sample Robot. This workstation is equipped with two rinsing pumps and two aspiration pumps each. They are used to clean the sensors in two Pick&Place modules and to empty the sample beaker after the analysis before it is placed back in the rack once again.

2.800.0020

Drive with write/read hardware for intelligent dosing units. With permanently attached cable (length 0.65 m).

2.1006.0010

Rod stirrer with permanently mounted cable (2.5 m) for direct connection to the OMNIS Sample Robot.

2.858.0030

The 858 Professional Sample Processor – Pump – Injector processes samples from 500 µL to 500 mL. The sample transfer takes place either with the installed bidirectional two-channel peristaltic pump or by means of an 800 Dosino. In addition, a six-way injection valve is available for the sample preparation.

2.800.0010

The 800 Dosino is a drive with write/read hardware for intelligent Dosing Units. With fixed cable (length 150 cm).

2.1010.0010

Main module for setting up an OMNIS Sample Robot Pick&Place in size S. This module is comprised of module and rack plates. It is already equipped with the main lift and one gripper. In addition to sample racks and gripper fingers, workstations such as Pick&Place module or a pump module are required for using it to set up a functioning Sample Robot. The selection of these components proceeds in accordance with the application.

2.1010.0120

Main module for setting up an OMNIS Sample Robot WSM in size S. This module is equipped with the module and rack plate for up to 2 racks and an OMNIS Workstation Module. It is already equipped with the main lift and a gripper. It must be equipped with sample racks, gripper fingers, and an OMNIS Workstation Module for sample processing in order to use it to set up a functioning Sample Robot. The selection of these components proceeds in accordance with the application.

2.1011.0010

Main module for setting up an OMNIS Sample Robot Pick&Place in size M. This module is equipped with the main lift and one gripper. One M/L module base and one rack base are each required to complete the setup. It must be equipped with sample racks, gripper fingers and workstations, e.g., Pick&Place module or a pump module in order to use it to set up a functioning Sample Robot. The selection of these components proceeds in accordance with the application.

2.1011.0120

Main module for setting up an OMNIS Sample Robot WSM in size M. This module is equipped with the module and rack plate for up to 5 racks and 4 workstations. It is already equipped with the main lift and a gripper. Sample racks, gripper fingers, and up to 2 OMNIS Workstation Modules for sample processing can also be attached in order to use it to set up a functioning Sample Robot. The selection of these components proceeds in accordance with the application.

2.1012.0010

Main module for setting up an OMNIS Sample Robot Pick&Place in size L. This module is equipped with the main lift and one gripper. One module base and two rack bases are required to complete the setup. It must be equipped with sample racks, gripper fingers and clients, e.g., Pick&Place module or a pump module in order to use it to set up a functioning Sample Robot. The selection of these components proceeds in accordance with the application.

2.1012.0120

Main module for setting up an OMNIS Sample Robot WSM in size L. This module is equipped with the module and rack plate for up to 7 racks and 4 workstations. It is already equipped with the main lift and a gripper. Sample racks, gripper fingers, and up to 2 OMNIS Workstation Modules for sample processing can also be attached in order to use it to set up a functioning Sample Robot. The selection of these components proceeds in accordance with the application.

2.1017.0010

Module for installation in the module plate of the OMNIS Sample Robot Oven. This workstation picks up the 2R sample vial and transports it from the handover position into the oven and then back again after the analysis is completed.

2.1017.1000

Module for installation in the module plate of the OMNIS Sample Robot Oven. This workstation picks up the 6 mL sample vial and transports it from the handover position into the oven and then back again after the analysis is completed.

2.1017.1010

Module for installation in the module plate of the OMNIS Sample Robot Oven. This workstation picks up the 8 mL sample vial and transports it from the handover position into the oven and then back again after the analysis is completed.

2.922.1000

Robust near-infrared spectroscopy for quality control of polymers, not only in laboratories, but also in production environments.The NIRS DS2500 Polymer Analyzer is the tried and tested, flexible solution for quality control and routine analysis of PE, PP, PET, polyamide, and other polymers in solid form along the entire production chain. Resistant to dust, moisture, vibrations, and temperature fluctuations, the NIRS DS2500 Polymer Analyzer is not only suitable for laboratory use, but also use in harsh production environments.The NIRS DS2500 Polymer Analyzer covers the full spectral range from 400 to 2,500 nm and delivers accurate results in less than one minute. The NIRS DS2500 Polymer Analyzer is ready for immediate use through pre-calibrations for PE, PP, PET, and polyamide (PA 6) and, thanks to its simple operation, supports users in their day-to-day routine tasks.

2.815.2110

The preparation system for solid samples that need to be homogenized, filtered and decanted in closed vials.The system consists of:1 x 815 Robotic USB Sample Processor XL1 x 136 Polytron with power supply unit1 x 772 Pump Unit1 x 786 Swing Head1 x reinforced 786 Swing Head1 x 800 Dosino

2.940.1100

The 940 Professional IC Vario ONE is the intelligent IC instrument for applications without suppression. The instrument can be used with any separation and detection methods.Typical areas of application:Anion and cation determinations without suppression; Analyses with UV/VIS detection with or without post-column derivatization; Applications with amperometric detection (e.g., sugar analysis); Trace analysis for cations with MiPCT;

2.940.1530

The 940 Professional IC Vario ONE/SeS/PP/Prep 3 is the intelligent IC instrument with sequential suppression with a peristaltic pump for suppressor regeneration in combination with Metrohm Inline Sample Preparation, e.g., Inline Neutralization or Inline Cation Removal. The instrument can be used with any separation and detection methods.Typical areas of application:Anion determinations with sequential suppression after Inline Neutralization; Online trace analysis with Inline Neutralization and subsequent MiPCT-ME; Anion analysis after cation removal in samples with high transition metal concentrations, e.g., electroplating baths;

2.848.2010

The Salt Titrino plus offers you the complete package for the analysis of chloride in a wide variety of samples. In addition to the determination methods described in detail, you also receive the complete accessories for your titrations. The package contains a titrator, a magnetic stirrer and an Ag Titrode, a maintenance-free electrode for precipitation titration with silver nitrate.

2.940.1140

The 940 Professional IC Vario ONE/HPG is the intelligent IC instrument without suppression with binary high-pressure gradient. It can be extended with the 942 Extension Modules to up to a quaternary gradient system. The instrument can be used with any separation and detection methods.Typical areas of application:Carbohydrate analysis with pulsed amperometric detection (PAD) after gradient elution; Gradient applications with UV/VIS detection with or without post-column derivatization;

2.940.1150

The 940 Professional IC Vario ONE/LPG is the intelligent IC instrument without suppression with low-pressure gradient. The instrument can be used with any separation and detection methods.Typical areas of application:Carbohydrate analysis with pulsed amperometric detection (PAD) after gradient elution; Gradient applications with UV/VIS detection with or without post-column derivatization;

2.940.1200

The 940 Professional IC Vario ONE/ChS is the intelligent IC instrument with chemical suppression. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Anion determinations with chemical suppression and conductivity detection; Organic acids with ion-exclusion chromatography and inverse suppression;

2.940.1300

The 940 Professional IC Vario ONE/ChS/PP is the intelligent IC instrument with chemical suppression and a peristaltic pump for suppressor regeneration. The instrument can be used with any separation and detection methods.Typical areas of application:Anion determinations with chemical suppression and conductivity detection; Organic acids with inverse suppression and conductivity detection;

2.940.1400

The 940 Professional IC Vario ONE/SeS is the intelligent IC instrument for applications with sequential suppression. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Anion or cation determinations with sequential suppression; Trace analysis for anions or cations; Online monitoring for anions or cations;

2.940.1430

The 940 Professional IC Vario ONE/SeS/Prep 3 is the intelligent IC instrument with sequential suppression in combination with Metrohm Inline Sample Preparation, e.g., Inline Neutralization or Inline Cation Removal. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Anion determinations with sequential suppression after Inline Neutralization; Online trace analysis with Inline Neutralization and subsequent MiPCT-ME; Anion analysis after cation removal in samples with high transition metal concentrations, e.g., electroplating baths;

2.940.1500

The 940 Professional IC Vario ONE/SeS/PP is the intelligent IC instrument with sequential suppression and a peristaltic pump for suppressor regeneration. The instrument can be used with any separation and detection methods.Typical areas of application:Anion or cation determinations with sequential suppression and conductivity detection; Trace analysis for anions or cations; Online monitoring for anions or cations;

2.940.2100

The 940 Professional IC Vario TWO is the intelligent two-channel IC instrument without suppression. The instrument can be used with any separation and detection methods.Typical areas of application:Two-channel applications without suppression for the determination of anions, cations, carbohydrates or polar, organic compounds; Combinations with conductivity, UV/VIS or amperometric detection;

MATi 03

Direct nonaqueous titration of pharmaceutical active ingredients and other substances in series of up to 59 samples. The system is noteworthy for its special resistance to organic solvents. The control of this system is handled by the proven OMNIS software, that can also be provided in an FDA-compliant version upon request.

2.848.1010

The Food/Beverage Titrino plus offers you the complete package for all conventional analyses of foods, beverages and wine. You receive an all-inclusive care package comprised of titrator, magnetic stirrer, electrode, electrolyte and storage solution for the Ecotrode Plus, the optimum pH glass electrode for aqueous acid-base titrations. Buffers for calibration are also included.Profit from our more than 60 years of application know-how. Almost 100 tried and tested methods are waiting to be used by you. Programming the titrator can be dispensed with. Simply load the method from the USB Memory Stick supplied in the scope of delivery. The methods were formulated in the light of the following publications:Official Methods of Analysis of the Association of Official Analytical Chemists (AOAC, USA); U.S. Environmental Protection Agency (EPA); Swiss Food Manual; German standard methods for the examination of water, waste water and sludge;

2.848.3010

The Oil Titrino plus offers you the complete package for the determination of the acid and base numbers of oil products. In addition to the determination methods described in detail, you also receive the complete accessories for your titrations. The package contains titrator, propeller stirrer and a Solvotrode easyClean, a pH glass electrode that is specialized for nonaqueous titrations.

ProfIC-Vario-08-Cation

The Professional IC Vario system with Metrohm Inline Matrix Elimination and conductivity detection enables the determination of cations or anions (non-suppressed) in difficult matrices.Typical areas of application:Trace analysis in polar solvents; Quality control in fuels, fuel mixtures, and biofuels; Quality management of chemicals; Schematic representation

ProfIC-Vario-14-Cation

The Professional IC Vario system with Metrohm's intelligent Pick-up Injection Technique (MiPuT) and conductivity detection enables the determination of cations or anions (non-suppressed) from the smallest of sample volumes.Typical areas of application:Universal use for all types of samples when only small sample amounts are available; Investigation of biochemical processes; Environmental sample extracts; Schematic representationInstallation instructions

2.940.1110

The 940 Professional IC Vario ONE/Prep 1 is the intelligent IC instrument without suppression in combination with MetrohmInline Sample Preparation, e.g., Inline Ultrafiltration or Inline Dialysis. The instrument can be used with any separation and detection methods.Typical areas of application:Anion and cation determinations without suppression after Inline Ultrafiltration or Inline Dialysis; UV/VIS applications after Inline Ultrafiltration or Inline Dialysis; Applications with amperometric detection after Inline Ultrafiltration or Inline Dialysis;

2.940.1240

The 940 Professional IC Vario ONE/ChS/HPG is the intelligent IC instrument with chemical suppression and binary high-pressure gradient. It can be extended with the 942 Extension Modules to up to a quaternary gradient system. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Gradient applications for anion determinations with chemical suppression;

2.940.1250

The 940 Professional IC Vario ONE/ChS/LPG is the intelligent IC instrument with chemical suppression and low-pressure gradient. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Gradient applications for anion determinations with chemical suppression;

2.940.1340

The 940 Professional IC Vario ONE/ChS/PP/HPG is the intelligent IC instrument with chemical suppression, a peristaltic pump for suppressor regeneration and binary high-pressure gradient. It can be extended with the 942 Extension Modules to up to a quaternary gradient system. The instrument can be used with any separation and detection methods.Typical areas of application:Gradient applications for anion determinations with chemical suppression;

2.940.1350

The 940 Professional IC Vario ONE/ChS/PP/LPG is the intelligent IC instrument with chemical suppression, a peristaltic pump for suppressor regeneration and low-pressure gradient. The instrument can be used with any separation and detection methods.Typical areas of application:Gradient applications for anion determinations with chemical suppression;

2.940.1440

The 940 Professional IC Vario ONE/SeS/HPG is the intelligent IC instrument with sequential suppression and binary high-pressure gradient. It can be extended with the 942 Extension Modules to up to a quaternary gradient system. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Gradient applications for anion or cation determinations with sequential suppression;

2.940.1450

The 940 Professional IC Vario ONE/SeS/LPG is the intelligent IC instrument with sequential suppression and low-pressure gradient. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Gradient applications for anion or cation determinations with sequential suppression;

2.940.1540

The 940 Professional IC Vario ONE/SeS/PP/HPG is the intelligent IC instrument with sequential suppression, a peristaltic pump for suppressor regeneration and binary high-pressure gradient. It can be extended with the 942 Extension Modules to up to a quaternary gradient system. The instrument can be used with any separation and detection methods.Typical areas of application:Gradient applications for anion or cation determinations with sequential suppression;

2.940.1550

The 940 Professional IC Vario ONE/SeS/PP/LPG is the intelligent IC instrument with sequential suppression, a peristaltic pump for suppressor regeneration and low-pressure gradient. The instrument can be used with any separation and detection methods.Typical areas of application:Gradient applications for anion or cation determinations with sequential suppression;

2.940.2200

The 940 Professional IC Vario TWO/ChS is the intelligent two-channel IC instrument with a chemical suppressor. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Parallel anion and cation determinations; Two-channel applications with various detectors;

2.940.2300

The 940 Professional IC Vario TWO/ChS/PP is the intelligent two-channel IC instrument with a chemical suppressor and a peristaltic pump for suppressor regeneration. The instrument can be used with any separation and detection methods.Typical areas of application:Parallel anion and cation determinations; Two-channel applications with various detectors;

2.940.2400

The 940 Professional IC Vario TWO/SeS is the intelligent two-channel IC instrument with sequential suppression (one channel). An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Standard instrument for parallel anion and cation determinations; Trace analysis for anions and cations; Online monitoring for anions and cations;

2.940.2500

The 940 Professional IC Vario TWO/SeS/PP is the intelligent two-channel IC instrument with sequential suppression (one channel) and a peristaltic pump for suppressor regeneration. The instrument can be used with any separation and detection methods.Typical areas of application:Standard instrument for parallel anion and cation determinations; Trace analysis for anions and cations; Online monitoring for anions and cations;

ProfIC-Vario-10-Anion

The Professional IC Vario system with Metrohm Inline Neutralization, sequential suppression and conductivity detection enables the determination of anions in matrices with extreme alkali, acid, or metal contamination.Typical areas of application:Trace analysis in bases and acids; Starter substances from the electroplating industry; Contamination in electroplating baths; Schematic representation

2.940.1120

The 940 Professional IC Vario ONE/Prep 2 is the intelligent IC instrument without suppression in combination with Metrohm Inline Sample Preparation, e.g., Inline Matrix Elimination or Inline Calibration. The instrument can be used with any separation and detection methods.Typical areas of application:Anion and cation determinations without suppression after Inline Matrix Elimination; Ultratrace analysis for cations with Inline Calibration;

ProfIC-Vario-08-Anion

The Professional IC Vario system with Metrohm Inline Matrix Elimination, sequential suppression and conductivity detection enables the determination of anions or cations in difficult matrices.Typical areas of application:Trace analysis in polar solvents; Quality control in fuels, fuel mixtures, and biofuels; Quality management of chemicals; Schematic representation

ProfIC-Vario-09-Cation

The Professional IC Vario system with Metrohm's intelligent inline preconcentration technique, Inline Matrix Elimination and conductivity detection enables ultratrace analysis down to the lowest ppt range (ng/L) of cations in complex matrices.Typical areas of application:Ultratrace analysis in samples from nuclear power plants and conventional power plants; Trace and ultratrace analysis in extraction agents and organics; Trace analysis in snow and ice; Schematic representationInstallation instructions

ProfIC-Vario-14-Anion

The Professional IC Vario system with Metrohm's intelligent Pick-up Injection Technique (MiPuT), sequential suppression and conductivity detection enables the determination of anions or cations from the smallest of sample volumes.Typical areas of application:Universal use for all types of samples when only small sample amounts are available; Investigation of biochemical processes; Environmental sample extracts; Schematic representationInstallation instructions

2.940.1410

The 940 Professional IC Vario ONE/SeS/Prep 1 is the intelligent IC instrument with sequential suppression in combination with Metrohm Inline Sample Preparation, e.g., Inline Ultrafiltration or Inline Dialysis. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Anion or cation determinations with sequential suppression after Inline Ultrafiltration or Inline Dialysis;

2.940.1510

The 940 Professional IC Vario ONE/SeS/PP/Prep 1 is the intelligent IC instrument with sequential suppression and peristaltic pump for suppressor regeneration in combination with Metrohm Inline Sample Preparation, e.g., Inline Ultrafiltration or Inline Dialysis. The instrument can be used with any separation and detection methods.Typical areas of application:Anion or cation determinations with sequential suppression after Inline Ultrafiltration or Inline Dialysis;

2.889.0030

The 889 IC Sample Center Basic – is a robust Autosampler for high sample throughput, optimized for the challenges of the modern analytic laboratory. It uses the x-y-z principle. A double needle system enables the penetration of vessel caps and septa.The sample transfer takes place either with a peristaltic pump in the IC system or with an 800 Dosino, e.g. when applying the intelligent Partial Loop Injection Technique.Supported with MagIC Net 4.1 and higher.

2.940.1420

The 940 Professional IC Vario ONE/SeS/Prep 2 is the intelligent IC instrument with sequential suppression in combination with Metrohm Inline Sample Preparation, e.g., Inline Matrix Elimination or Inline Calibration. An 800 Dosino can be used for the regeneration of the suppressor. The instrument can be used with any separation and detection methods.Typical areas of application:Anion or cation determinations with sequential suppression after Inline Matrix Elimination; Ultratrace analysis for anions or cations with Inline Calibration;

2.940.1520

The 940 Professional IC Vario ONE/SeS/PP/Prep 2 is the intelligent IC instrument with sequential suppression and a peristaltic pump for suppressor regeneration in combination with Metrohm Inline Sample Preparation, e.g., Inline Matrix Elimination or Inline Calibration. The instrument can be used with any separation and detection methods.Typical areas of application:Anion or cation determinations with sequential suppression after Inline Matrix Elimination; Ultratrace analysis for anions or cations with sequential suppression and Inline Calibration;

ProfIC-Vario-09-Anion

The Professional IC Vario system with Metrohm's intelligent inline preconcentration technique, Inline Matrix Elimination, sequential suppression, and conductivity detection enables ultratrace analysis down to the lowest ppt range (ng/L) of anions or cations in complex matrices.Typical areas of application:Ultratrace analysis in samples from nuclear power plants and conventional power plants; Trace and ultratrace analysis in extraction agents and organics; Trace analysis in snow and ice; Schematic representation

ProfIC-Vario-14-AnCat

The Professional IC Vario system with Metrohm's intelligent Pick-up Injection Technique (MiPuT), sequential suppression and conductivity detection enables the determination of anions and cations from the smallest of sample volumes.Typical areas of application:For universal application for all types of samples when only small sample amounts are available; Investigation of biochemical processes; Environmental sample extracts; Schematic representation

2.888.0110

High-end titrator with built-in buret driveincluding 900 Touch Control, 801 Stirrer magnetic stirrer, exchange unit (20 mL) and combined "Ecotrode plus" pH glass electrode; dynamic (DET), monotonic (MET) and endpoint titration (SET); four MSB connectors; one galvanically isolated measuring interface (also for intelligent "iTrodes" electrodes); USB connector;

2.921.1310

Rapid, nondestructive analyses of tablets, capsules and other solid-state dosage forms.The NIRS XDS MasterLab Analyzer enables the rapid, nondestructive analyses of solid-state dosage forms such as tablets, capsules, film-coated tablets, gel tablets and gel capsules for manufacturers in the pharmaceuticals industry. Solids in vials can also be analyzed with the NIRS XDS MasterLab Analyzer. The analysis takes place in reflection or transmission mode. The sample input proceeds via a sample slide that can be moved in x and y direction and that is designed for trays with several tablets and/or vials. Analyses of individual samples are optimized with an iris. An optionally available coarse granular sample cell for coarse granular substances extends analysis to include practically all solid forms ranging from fine powders to coarse granular materials, e.g., pellets and flakes.

ProfIC-Vario-09-AnCat

The Professional IC Vario system with Metrohm's intelligent inline preconcentration technique, Inline Matrix Elimination, sequential suppression and conductivity detection enables ultratrace analysis down to the lowest ppt range (ng/L) of anions and cations in complex matrices.Typical areas of application:Ultratrace analysis in samples from nuclear power plants and conventional power plants; Trace and ultratrace analysis in extraction agents and organics; Schematic representationInstallation instructions

ProfIC-Vario-11-Anion

The Professional IC Vario system with Metrohm Inline Neutralization, Metrohm's intelligent inline preconcentration technique and Inline Matrix Elimination and sequential suppression and conductivity detection enables the analysis of anions in complex matrices from the ultratrace down to the mg/L range.Typical areas of application:Trace analysis in concentrated bases and acids; Ultratrace analysis for nuclear power plants in matrices, such as lithium hydroxide/boric acid; Schematic representation

2.904.0010

High-end titrator for potentiometric titration with one measuring interface and internal buret drive. internal buret drive; dynamic (DET), monotonic (MET), and endpoint titration (SET); Measurement with ion-selective electrodes (MEAS CONC); Dosing functions with monitoring, Liquid Handling; four MSB connectors for additional stirrers or dosing systems; "iTrode" intelligent electrodes; USB connector; For use with OMNIS Software, tiamo software, or Touch Control unit; Compliance with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.905.0010

High-end titrator for potentiometric titration with one measuring interface for use with Dosino dosing systems. up to four dosing systems of the 800 Dosino type; dynamic (DET), monotonic (MET), and endpoint titration (SET); Measurement with ion-selective electrodes (MEAS CONC); Dosing functions with monitoring, Liquid Handling; four MSB connectors for additional stirrers or dosing systems; "iTrode" intelligent electrodes; USB connector; For use with OMNIS Software, tiamo software, or Touch Control unit; Compliance with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.902.0010

High-end potentiometric titrator for endpoint titration (SET), as well as enzymatic and pH-STAT titrations (STAT) with one measuring interface. up to four dosing device systems of the 800 Dosino type; Dosing functions with monitoring, liquid handling and tandem dosing; four MSB connectors for additional stirrers or dosing device systems; can be supplemented with one additional measuring interface; USB connector; For use with OMNIS Software, tiamo software, or Touch Control; Complies with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.904.0020

High-end titrator for potentiometric titration with two measuring interfaces and internal buret drive. internal buret drive; dynamic (DET), monotonic (MET), and endpoint titration (SET); Measurement with ion-selective electrodes (MEAS CONC); Dosing functions with monitoring, Liquid Handling; four MSB connectors for additional stirrers or dosing systems; "iTrode" intelligent electrodes; USB connector; For use with OMNIS Software, tiamo software, or Touch Control unit; Compliance with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.905.0020

High-end titrator for potentiometric titration with two measuring interfaces for use with Dosino dosing systems. up to four dosing systems of the 800 Dosino type; dynamic (DET), monotonic (MET), and endpoint titration (SET); Measurement with ion-selective electrodes (MEAS CONC); Dosing functions with monitoring, Liquid Handling; four MSB connectors for additional stirrers or dosing systems; "iTrode" intelligent electrodes; USB connector; For use with OMNIS Software, tiamo software, or Touch Control unit; Compliance with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.906.0010

High-end titrator for potentiometric and volumetric Karl Fischer titration with one measuring interface and internal buret drive. built-in buret drive; dynamic (DET), monotonic (MET) and endpoint titration (SET), enzymatic and pH-STAT titrations (STAT), Karl Fischer titration (KFT); Measurement with ion-selective electrodes (MEAS CONC); "iTrode" intelligent electrodes; Dosing functions with monitoring, liquid handling; four MSB connectors for additional stirrers or dosing device systems; USB connector; For use with OMNIS Software, tiamo software, or Touch Control; Complies with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.907.0010

High-end titrator for potentiometric and volumetric Karl Fischer titration with one measuring interface and Dosino dosing units. up to four dosing device systems of the 800 Dosino type; dynamic (DET), monotonic (MET) and endpoint titration (SET), enzymatic and pH-STAT titrations (STAT), Karl Fischer titration (KFT); Measurement with ion-selective electrodes (MEAS CONC); "iTrode" intelligent electrodes; Dosing functions with monitoring, liquid handling; four MSB connectors for additional stirrers or dosing device systems; USB connector; For use with OMNIS Software, tiamo software, or Touch Control; Complies with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.906.0020

High-end titrator for potentiometric and volumetric Karl Fischer titration with 2 measuring interfaces and internal dosing drive. built-in dosing drive; dynamic (DET), monotonic (MET) and endpoint titration (SET), enzymatic and pH-STAT titrations (STAT), Karl Fischer titration (KFT); Measurement with ion-selective electrodes (MEAS CONC); Dosing functions with monitoring, liquid handling; 4 MSB connectors; 2 galvanically isolated measuring interfaces; USB connector; For use with OMNIS Software, tiamo software, or Touch Control; Complies with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.907.0020

High-end titrator for potentiometric and volumetric Karl Fischer titration with two measuring interfaces and Dosino dosing units. up to four dosing device systems of the 800 Dosino type; dynamic (DET), monotonic (MET) and endpoint titration (SET), enzymatic and pH-STAT titrations (STAT), Karl Fischer titration (KFT); "iTrode" intelligent electrodes; Measurement with ion-selective electrodes (MEAS CONC); Dosing functions with monitoring, liquid handling; four MSB connectors for additional stirrers or dosing device systems; USB connector; For use with OMNIS Software, tiamo software, or Touch Control; Complies with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required;

2.907.1020

The Pharm Titrando is based on the 907 Titrando and offers a complete package for the most common analyses of pharmaceutical products. Apart from the titration software tiamoTM full and determination methods described in detail, you will also receive comprehensive accessories for your titrations.

2.780.0010

In addition to pH, voltage and temperature measurement, the 780 pH Meter also offers an automatic stirrer control, a multi-point calibration with up to nine buffers, a method memory and various monitoring functions. The automatic pH electrode test in conformance with GLP permits objective assessment of the electrode. The large backlit multi-line display provides an overview and makes the individual settings easy. The bi-directional RS-232 interface enables data transfer to a printer or PC.

2.781.0010

In addition to pH, ion, voltage and temperature measurement, the combined 781 pH/Ion Meter also offers an automatic stirrer control, a multi-point calibration with up to nine buffers (pH mode), a method memory and various monitoring functions. The automatic pH electrode test in conformance with GLP permits objective assessment of the electrode. The large backlit multi-line display provides an overview and makes the individual settings easy. The bi-directional RS-232 interface enables data transfer to a printer or PC.Three different modes are available for ion measurement: direct measurement, standard or sample addition. In the case of fully automated standard addition with an optional Dosimat, only the concentration of the standard and the desired quantity of addition steps need to be entered, the pH/ion meter takes care of the rest. Up to 19 standards can be used for the calibration for direct measurement.

2.895.0010

The 895 Professional PVC Thermomat is an analysis system for the automatic determination of the thermostability of polyvinyl chloride (PVC) and related copolymers. With eight measuring positions in two heating blocks. The built-in display shows the status of the instrument and each individual measuring position. Start buttons for every measuring position enable the measurement start on the instrument. Cleaning effort can be reduced to a minimum through the use of practical disposable reaction vessels and dishwasher-safe accessories. This saves time and costs and significantly improves accuracy and reproducibility.All accessories necessary for carrying out determinations are included in the scope of delivery. The StabNet software is required for instrument control, data recording and evaluation and for data storage.

2.867.0110

High-end pH/ion meter based on the 867 pH Module, including 900 Touch Control, 854 iConnect and intelligent "iUnitrode" pH glass electrode.In addition to measurements of pH, temperature, mV, Ipol, Upol and concentration, the pH Module can perform standard additions (manual, dos, autodos) and Liquid Handling (add, prep, empty). It enables the use of both conventional and intelligent sensors for measuring. Also integrated in the software is an automatic GLP-compliant pH electrode test.The pH Module has two USB interfaces for connecting printers, barcode readers or sample changers and four MSB interfaces for stirrers or Dosinos (for the addition of auxiliary solutions or for standard addition).In combination with the Touch Control, it is in compliance with GLP and FDA 21 CFR part 11 requirements.

2.867.0010

Module for pH/ion measurement as supplement to a Titrando or "stand-alone" in combination with a 900 Touch Control.In addition to measurements of pH, temperature, mV, Ipol, Upol and concentration, the pH Module can perform standard additions (manual, dos, autodos) and Liquid Handling (add, prep, empty). It enables the use of both conventional and intelligent sensors for measuring. Also integrated in the software is an automatic GLP-compliant pH electrode test.The pH Module has two USB interfaces for connecting printers, barcode readers or sample changers and four MSB interfaces for stirrers or Dosinos (for the addition of auxiliary solutions or for standard addition).For use with OMNIS Software, tiamo software, or Touch Control unit. Compliance with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required.

2.1072.0010

Near-infrared spectrometer for liquid, solid, and viscous samples. Developed and produced in accordance with Swiss quality standards, the OMNIS NIR Analyzer is the near-infrared spectroscopy (NIRS) solution for routine analysis along the entire production chain. Its application of the latest technologies and its integration in the modern OMNIS Software are reflected in its speed, operability and flexible utilization of this NIR spectrometer.Overview of the advantages of the OMNIS NIR Analyzer Liquid/Solid:Measurements of fluid, solid, and viscous samples in less than 10 seconds; Fast sequential measurement of liquid and solid samples without conversion of the system; Simple integration in an automation system or link with additional analysis technologies (titration); Supports numerous sample vessels; Highlights of measurements of liquids:Temperature control on the sample from 25–80 °C; Automatic detection of the sample; Highlights of measurements of solids:Automated multi-position measurements for reproducible results, even with nonhomogeneous samples;