FAQs – MagIC Net

There are time program commands available with which drift, noise, and the current measured value of a detector can be determined.

These commands can be inserted at the appropriate place in the "Time program". You need to create a new line in the "Time program" for this. The corresponding commands are given under the respective detector. A comment can be entered for a measured detector value. Drift and noise also require definition of a certain measuring period. To obtain correct values for drift and noise, it must be ensured that no changes to the baseline occur during the respective measuring period.

There are three types of subprograms:

1. "Sequence": The commands of the "Subprogram" are processed first before proceeding with the next line in the "Main program".
2. "Loop": Analogous to Sequence, but the commands of the "Subprogram" are executed consecutively n times. The number of runs can be fixed or defined at the start of the loop by means of a formula.
3. "Parallel": This "Subprogram" runs parallel to the "Main program" or to the respective "Subprogram".

Conditions enable MagIC Net to make decisions automatically. They can be used to decide, e.g., whether a subprogram is executed or skipped.

Variables can also be compared and, depending on the result, different processes can be triggered. This allows a decision, e.g., on the basis of a comparison of the peak areas of the sample and a standard whether a sample has to be diluted further and then analyzed again.

"Common variables" are variables (number, texts, date/time) for determinations that must be stored externally (outside the determination), e.g., a counter that has to be applied to the next determination.

"Common variables" have an initial value. This is read out by a determination and can thus be used. The content of a "Common variable" can be changed and then stored again in a determination. The new value is then available for the next determination.

The recovery rate can be calculated if a determination of the sample type "Spiking" is carried out after the "Sample".

The concentrations of the spiking solution are defined in the method. More than one spiking solution can be defined.

The example methods are saved as *.imet files during installation in a subdirectory of the program directory.

If such an example method is to be used, it must be imported using "Method manager" into a "Method group". If this method is to be used directly with the existing IC system, the same devices and module names must be used. If "Common variables" are used in the method, they must be created first under "Configuration".

It is possible to count the sample injections in MagIC Net. As soon as the corresponding number is reached, you can use the "Time program command">"Insert new line" in the "Sample table" to insert a sample line with the data of the sample for a check standard.

Statistics functions are available in the method for multiple injections. They can be used to calculate the mean value, the absolute and relative standard deviation as well as the minimum and maximum value of a "Result".

A Method is used to define what, how, and when something is carried out and determined.

In MagIC Net, the method is composed of four windows.

"Devices" shows all instruments and modules used in the method along with their parameters. Clicking on the corresponding icon opens the parameters of this component so they can be adjusted.The "Analysis" is also created in this window. "Hardware assignment", "Data acquisition", and "Accessories" are defined here. The window "Evaluation – Components" has the sections Integration, Analysis Components, Standards, Calibration, and Results. Under "Results", it is possible to define "User-defined results", "Statistics", "Monitoring", etc. The third method window, "Time program", defines the exact analysis run. This defines all steps that the IC system or MagIC Net must execute. A time program can comprise a few consecutive steps or complex interleaving of subprograms. The fourth window shows the last chromatogram with the current calibration.

The "Time program" in the "Method" consists of at least one "Main program". This defines the chronological sequence of the analysis run (sampler commands, injection, start of data acquisition, etc.). Subprograms can be inserted to prevent the "Time program" becoming too complex or to allow functions that are independent of the sample.

The subprograms can be linked to "Conditions" that are used to decide whether they are to be started or skipped. For example, a subprogram can be created that is only executed for determinations used for calibrating the method.

Once a "Method" has been loaded, its plausibility can be checked with the "Method check" (green check mark or under the "File" menu).