Aksesuar Bulucu

2.1056.0930

The OMNIS Waste Collector Unit is used to collect the liquid streams entering the waste. The collector's transparent housing allows for visual flow verification of up to 4 liquid streams. If more than 4 channels are fed into the drainage system, then an additional waste collector can be installed on the reagent organizer.Specifications:- Number of channels: 4- Transparent design for visual flow verification

6.01532.110

Transfer tubing 10 mL, FEP, M6 for installation in the MISP unit for the transfer or short-term storage of liquids. Prevents contamination of the dosing unit.FEP tubing is chemically inert and flexible. It has a larger inner diameter than capillaries, which means that larger liquid volumes can be conveyed faster.Typical application:Preconcentration technique (MiPCT)Dilution technique (MIDT)

6.01532.120

Transfer tubing 10 mL, PEEK, OD ⅛" for installation in the MISP unit for the transfer or short-term storage of liquids. Prevents contamination of the dosing unit.PEEK tubing is chemically inert and serves as an alternative to PTFE (FEP/PFA) tubing in order to prevent possible fluoride contamination. It has a larger inner diameter than capillaries, which means that larger liquid volumes can be conveyed faster.Typical application:Preconcentration technique (MiPCT)

6.01532.130

Transfer tubing 5 mL, OD 1/8" for installation in the MISP unit for the transfer or short-term storage of liquids. Prevents contamination of the dosing unit.FEP tubing is chemically inert and flexible. It has a larger inner diameter than capillaries, which means that larger liquid volumes can be conveyed faster.Typical application:Preconcentration technique (MiPCT and MiPCT-ME)Dilution technique (MIDT)

6.01532.140

Transfer tubing LQH, FEP, OD 1/8" for installation in the MISP unit for the transfer or short-term storage of liquids. Prevents contamination of the dosing unit.FEP tubing is chemically inert and flexible. It has a larger inner diameter than capillaries, which means that larger liquid volumes can be conveyed faster.Typical application:Dilution technique (MIDT)

6.01562.100

Transfer capillary, 2 ml, PEEK for installation in the MISP unit for the transfer or short-term storage of liquids. Prevents contamination of the dosing unit.PEEK tubing is chemically inert and serves as an alternative to PTFE (FEP/PFA) tubing in order to prevent possible fluoride contamination. It has a larger inner diameter than capillaries, which means that larger liquid volumes can be conveyed faster.Typical application:Partial Loop injection Technique (MiPT)Preconcentration technique (MiPCT)

6.01602.100

Bottle cap GL 45 for eluent, regenerant, reagent, and rinsing bottles, with connectors for the adsorber tube and the aspiration tubing.

6.01602.110

Cap S 40 for 10 L containers.

6.01608.000

Bottle 2 L (PP) designed for OMNIS Reagent Organizer, with volume indication for eluent, regenerant, reagent, and rinsing solutions.

6.01803.110

Pre-cut PTFE capillary with identification label for OMNIS IC

6.01803.120

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01805.500

Pre-cut FEP tubing with identification label for OMNIS IC

6.01808.000

Connector for drain tubing.

6.01808.010

Connector for drain tubing.

6.01808.020

Connector for drain tubing.

6.01808.030

Connector for drain tubing.

6.01808.100

Practical tubing fixation for the reagent organizer, providing secure guidance of the drain tubing through the IC instrument.

6.01810.000

Mounting fixture for the installation of the preheating cartridge and PCR cartridge on the OMNIS IC column tray. Provides secure and organized integration of the cartridges within the system setup.

6.01815.000

Spiral band for holding together different tubings or cables.

6.01816.000

Silicone drain tube

6.01826.010

Pump tubing with an inner diameter of 0.5 mm for use with the Peristaltic Pump Unit in the OMNIS IC system. The tubing enables controlled and reliable transport of liquids for examples for dialysis, suppressor regeneration, or PCR solutions. It is designed for consistent flow performance during operation. Its material properties support stable functioning under routine analytical conditions.

6.01826.020

Pump tubing with an inner diameter of 1.0 mm for use with the Peristaltic Pump Unit in the OMNIS IC system. The tubing enables controlled and reliable transport of liquids for examples for sample solutions. It is designed for consistent flow performance during operation. Its material properties support stable functioning under routine analytical conditions.

6.01831.100

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.110

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.140

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.150

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.160

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.170

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.180

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.190

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.200

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.210

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.220

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.230

Pre-cut PEEK capillary for OMNIS IC

6.01831.240

Pre-cut PEEK capillary for OMNIS IC

6.01831.250

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.260

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.270

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.280

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.290

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.300

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.310

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01831.320

Pre-cut PEEK capillary with identification label for OMNIS IC

6.01903.100

Magnetic stirrer in tablet form to reduce possible abrasion on the supply bottle (6.01608.000 bottle PP, 2 L, GL 45).

6.02006.100

Base plate for fastening T connectors in the OMNIS MISP Unit.

6.02006.110

Holder for fastening trap columns in the OMNIS MISP Unit.

6.02006.120

Holder for fastening T connectors on the fixation bar in the OMNIS IC.

6.02009.000

Holder for 10 L container with integrated volume sensor.

6.02027.000

Clip for vertical fastening of capillaries and tubing in the OMNIS IC.Quantity: 2 pieces

6.02027.010

Clip for fastening PEEK capillaries in the OMNIS Column Thermostat Unit.

6.02027.020

Clip for fastening PEEK capillaries in the OMNIS Column Thermostat Unit.

6.02027.030

Clip for fastening the inlet capillary to the column when using the OMNIS Column Holder Unit.

6.02027.040

Clip for horizontal fastening of capillaries and tubing in the OMNIS IC.Quantity: 2 pieces

6.02027.050

Clip for horizontal fastening of accessories in the OMNIS IC.Quantity: 2 pieces

6.02040.000

Tray for accommodating sample racks in the OMNIS IC Autosampler. The tray provides a stable base for secure placement and precise positioning of sample racks during automated sampling. Its geometry is designed to ensure stable handling and reliable operation within routine analytical workflows. The tray can be seamlessly integrated into the autosampler system and easily removed to allow convenient loading and preparation of sample racks directly on the laboratory bench before placement in the autosampler.

6.02040.010

Cooled tray for accommodating sample racks in the OMNIS IC Autosampler. The tray maintains samples at a controlled low temperature, supporting the analysis of temperature-sensitive compounds. Rack positioning and handling correspond to the standard AS Tray, ensuring reliable and precise operation during automated sampling. The tray can be seamlessly integrated into the autosampler system and can be easily removed to allow convenient loading and preparation of sample racks directly on the laboratory bench before placing in the autosampler.

6.02041.500

Sample rack for holding 24 x 10 mL vials in the OMNIS IC Autosampler. Rack geometry is matched to vial dimensions to ensure precise positioning and stable handling during automated sampling. The racks can be seamlessly mounted on the AS/ASCOOL Tray.

6.02041.510

Sample rack for holding 40 x 5 mL vials in the OMNIS IC Autosampler. Rack geometry is matched to vial dimensions to ensure precise positioning and stable handling during automated sampling. The racks can be seamlessly mounted on the AS/ASCOOL Tray.

6.02041.520

Sample rack for holding 48 x 11 mm OD vials in the OMNIS IC Autosampler. Rack geometry is matched to vial dimensions to ensure precise positioning and stable handling during automated sampling. The racks can be seamlessly mounted on the AS/ASCOOL Tray.

6.02041.530

Sample rack for holding 6 x 50 mL bottles in the OMNIS IC Autosampler. Rack geometry is matched to vial dimensions to ensure precise positioning and stable handling during automated sampling. The racks can be seamlessly mounted on the AS/ASCOOL Tray.

6.02041.540

Sample rack for holding 12 x 22mm OD vials in the OMNIS IC Autosampler. Rack geometry is matched to vial dimensions to ensure precise positioning and stable handling during automated sampling. The racks can be seamlessly mounted on the AS/ASCOOL Tray.

6.02041.550

Sample rack for holding 2 x 200 mL bottles in the OMNIS IC Autosampler. Rack geometry is matched to vial dimensions to ensure precise positioning and stable handling during automated sampling. The racks can be seamlessly mounted on the AS/ASCOOL Tray

6.02050.000

Bottle holder for Eluent bottle PP 2 L on OMNIS IC Reagent Organizer.

6.02050.010

Bottle fixation for Eluent bottle PP 2 L on OMNIS IC Reagent Organizer.

6.02050.100

Bottle holder for glass bottles 1 L or 2 L on OMNIS IC Reagent Organizer.

6.02050.200

Bottle retainer for Eluent bottle PP 2 L on OMNIS IC Reagent Organizer Liquid Control.

6.02050.210

Container Fixation onto Volume Sensor Holder, Container 10 L.

6.02061.000

Organizer for reagent and eluent bottles for OMNIS IC instruments.

6.02061.100

Base plate for OMNIS IC modules and preconfigured instruments (OMNIS IC S, M, L).

6.02061.110

Intelligent drip collector for Base plate.

6.02061.120

Intelligent drip collector for Extension.

6.02061.130

Drip collector for Unit, mounted on fixation bar, Extension.

6.02061.200

Endplate between Extension or Autosampler and Reagent Organizer or Reagent Organiser Liquid Control.

6.02102.100

Remote cable to connect the OMNIS with third party instruments, e.g., mass spectrometers.

6.02104.100

Sensor cable to connect the Volume Sensor Holder, Container 10 L to the OMNIS IC.

6.02107.000

Network cable (1 m) for connecting one OMNIS instrument to an Ethernet Router, Ethernet Switch or local network

6.02107.010

Network cable (2 m) for connecting one OMNIS instrument to an Ethernet Router, Ethernet Switch or local network

6.02107.040

Network cable (0.3 m) for connecting one OMNIS instrument to an Ethernet Router, Ethernet Switch or local network

6.02122.120

Power cord (0.35 m) for connecting OMNIS Extension Modules

6.02122.130

Power cord (1 m) for connecting OMNIS Extension Modules

6.02601.060

Fixation bar for OMNIS IC Extention Module.

6.02603.000

Fall prevention fixture for fastening the OMNIS IC on the table. Useful for the installation, e.g., on an oil platform, on a ship, in an airplane, in a bus or in earthquake-prone areas.

6.02621.010

Multi-function tool for performing maintenance on the OMNIS High-Pressure Pump Unit.

6.02624.100

Sample needle for OMNIS IC Autosampler and OMNIS IC Autosampler COOL, metal-free.

6.02705.100

Clip for guiding capillaries and tubing in the 948 Continuous IC Module, CEP.

6.02741.000

Piston seal for OMNIS IC High-Pressure Pump Unit.

6.02741.030

Maintenance set for piston seal wash of the OMNIS IC High-Pressure Pump Unit.

6.02743.017

Disposable sample vials with volume indication produced from high-quality polystyrene (PS), specifically designed for use with the OMNIS IC Autosamplers. With a volume of 10 mL and an optimized geometry (flat-bottom), these vials ensure seamless integration, secure handling, and reliable automation.Produced and packed under cleanroom conditions (cleanroom class 7 according to DIN ISO 14644), Metrohm sample vials are engineered for high-purity applications. They are validated to meet minimal contamination levels, making them ideal for trace analysis in ion chromatography, where even small impurities can affect results.Quantity: 200 pieces

6.02743.020

Disposable sample vials with volume indication produced from high-quality polystyrene (PS), specifically designed for use with the OMNIS IC Autosamplers. With a volume of 5 mL and an optimized geometry (flat-bottom), these vials ensure seamless integration, secure handling, and reliable automation.Produced and packed under cleanroom conditions (cleanroom class 7 according to DIN ISO 14644), Metrohm sample vials are engineered for high-purity applications. They are validated to meet minimal contamination levels, making them ideal for trace analysis in ion chromatography, where even small impurities can affect results.Quantity: 2000 pieces

6.02743.027

Disposable sample vials with volume indication produced from high-quality polystyrene (PS), specifically designed for use with the OMNIS IC Autosamplers. With a volume of 5 mL and an optimized geometry (flat-bottom), these vials ensure seamless integration, secure handling, and reliable automation.Produced and packed under cleanroom conditions (cleanroom class 7 according to DIN ISO 14644), Metrohm sample vials are engineered for high-purity applications. They are validated to meet minimal contamination levels, making them ideal for trace analysis in ion chromatography, where even small impurities can affect results.Quantity: 200 pieces

6.02743.040

High-quality polystyrene (PS) sample vial designed for seamless use with the OMNIS IC Autosampler and for the safe handling and analysis of samples, reagents, and standards. Manufactured and packaged under controlled cleanroom conditions (ISO Class 7 according to DIN EN ISO 14644-1), the vial ensures low contamination levels and dependable performance in routine laboratory workflows.Quantity: 1 piece

6.02743.070

Caps for polystyrene sample vials 10 mL made from polypropylene. The caps are produced and packed under cleanroom conditions (cleanroom class 7 according to DIN ISO 14644) and are suitable for high-purity IC applications.Quantity: 2000 pieces

6.02743.077

Caps for polystyrene sample vials 10 mL made from polypropylene. The caps are produced and packed under cleanroom conditions (cleanroom class 7 according to DIN ISO 14644) and ensure high-purity IC applications.Quantity: 200 pieces

6.02743.080

Caps for polystyrene sample vials 5 mL made from polypropylene. The caps are produced and packed under cleanroom conditions (cleanroom class 7 according to DIN ISO 14644) and ensure high-purity IC applications.Quantity: 2000 pieces

6.02743.087

Caps for polystyrene sample vials 5 mL made from polypropylene. The caps are produced and packed under cleanroom conditions (cleanroom class 7 according to DIN ISO 14644) and ensure high-purity IC applications.Quantity: 200 pieces

6.02743.097

Screw cap with integrated septum designed for the secure storage and handling of samples, standards, and reagents. The septum enables automated sample access while minimizing contamination and evaporation, making it ideal for automated laboratory workflows. Its robust design ensures reliable sealing and dependable performance during sample preparation and analysis.Quantity: 12 pieces

6.02744.000

Fixation for sample needle onto the needle drive of the OMNIS IC Autosampler and OMNIS IC Autosampler COOL.

6.02744.010

Flangeless fitting for 1/8'' tubing.Quantity: 2 pcs

6.02744.020

T connector for 3 M6 tubings.

6.02744.030

T connector for 2 capillaries and 1 M6 tubing.

6.02744.060

Adapter for purging the aspiration tube with solution

6.02744.110

Flangeless ferrule for 1/8'' tubing.Quantity: 4 pieces

6.02762.100

Mixing vessel for inline dilution for the OMNIS IC Autosampler and OMNIS IC Autosampler COOL.

6.02762.110

Lid for the dilution vessel of the OMNIS IC Autosampler or OMNIS IC Autosampler COOL.

6.02765.000

Waste collector for up to four waste capillaries.

6.02800.000

Blind cover for an empty unit spot.

6.02816.000

20 mL syringe made of PP, with luer connector.

6.02824.000

Pump piston for OMNIS IC High Pressure Pump.

6.02824.010

Metal-free check valve for the outlet side of the OMNIS IC High Pressure Pump Unit.

6.02824.020

Metal-free check valve for the outlet side of the OMNIS High-Pressure Pump Unit.

6.02837.030

CO2 Absorber (Tube) with a Luer adapter; protects reagents and eluents from particles and ensures consistent retention times for CO2-sensitive eluents.

6.02837.040

Filter tube with Luer adapter, protects eluents and reagents from particles.

6.02837.110

Absorber cartridge for removing CO₂ from the air drawn in by the OMNIS MCS unit ensures that the baseline remains stable and consistent.

6.02841.120

Rinse station for needle rinsing for the OMNIS IC Autosampler and OMNIS IC Autosampler COOL.

6.02842.010

Coupling nut for OMNIS Actuator Unit.

6.02842.020

Connecting piece with inlets and outlets for OMNIS MSM and SPM.

6.02842.030

Coupling nut for OMNIS MSM Unit.

6.02842.040

Rotor housing to upgrade an OMNIS Actuator Unit into an OMNIS MSM Unit.

6.02845.000

Cartridge containing the eluent preheating capillary to be mounted in the OMNIS Column Thermostat Unit.

6.02845.100

Cartridge containing the PCR capillary to be mounted in the OMNIS IC Thermostate Unit.

6.02860.000

Sensor bar for OMNIS IC MFM Unit.

6.05000.000

OMNIS IC accessory set required for installation, daily work, and maintenance.The set contains the most necessary tools and accessories for simple tasks related to the OMNIS IC device.

6.05000.030

Accessory set to complete the installation of the OMNIS IC M module.

6.05000.120

6.05000.130

6.05000.140

6.05000.150

6.05000.160

6.05331.030

Accessory set for Ultrafiltration in OMNIS IC: Inline ultrafiltration allows the sample to be separated from contained particles. The main component of the Metrohm Inline Ultrafiltration system is the ultrafiltration cell. The ultrafiltration cell is suitable for sample filtration with high demands on filtration efficiency and sample throughput. This equipment is for the setup with a combination of the Peristaltic Pump Unit and the Dosing Drive Unit.Prerequisites:OMNIS IC S/M/L with OMNIS IC AS/ASCOOL, including:available OMNIS Dosing Drive Unit; available OMNIS Peristaltic Pump Unit channel; available OMNIS MISP Unit; AS/ASCOOL equipped with a switching valve 3/2, UNF;

6.05331.040

Accessory set for dilution in OMNIS IC: This technique allows samples with excessively high ion concentrations or highly concentrated sample matrices to be diluted. The required sample volume is precisely aspirated by the OMNIS Dosing Drive Unit.The sample and the dilution solution are mixed in the dilution station, ensuring the sample is diluted and completely homogenized. Additionally, with the Inline Dilution technique, calibration using a single standard solution is possible.Specifications:Maximum dilution factor: 2000; Accuracy: <1.5% up to DF 100, <2.5% up to DF 1000; Reproducibility (n=9): <1% up to DF 1000; Carry over: < 0.003%; Prerequisites:OMNIS IC S/M/L, including:available OMNIS Dosing Drive Unit; available OMNIS MISP Unit; AS/ASCOOL equipped with:dilution station and; switching valve 3/2, M6;

6.05331.050

Accessory set for Ultrafiltration in OMNIS IC: Inline ultrafiltration allows the sample to be separated from contained particles. The main component of the Metrohm inline ultrafiltration system is the ultrafiltration cell. The ultrafiltration cell is suitable for sample filtration with high demands on filtration efficiency and sample throughput. This equipment is for the setup with a Peristaltic Pump Unit only.Prerequisites:OMNIS IC S/M/L with OMNIS IC AS/ASCOOL, including:2 available OMNIS Peristaltic Pump Unit channels; available OMNIS MISP Unit;

6.05331.060

Accessory set for the combination of dilution with Ultrafiltration in OMNIS IC: This technique allows samples with excessively high ion concentrations or highly concentrated sample matrices to be diluted. The required sample volume is precisely aspirated by the OMNIS Dosing Drive Unit.Additionally, inline ultrafiltration allows the sample to be separated from the particles it contains. This combined technique allows calibration with only one standard solution.Prerequisites:OMNIS IC S/M/L with OMNIS IC AS/ASCOOL, including:available OMNIS Dosing Drive Unit; available OMNIS Peristaltic Pump Unit channel; available OMNIS MISP Unit; AS/ASCOOL equipped with dilution station and switching valve 3/2, UNF;

6.05331.070

Accessory set for Partial Loop Injection in OMNIS IC: With this technique, the 250 μL sample loop can be filled with a defined volume. The OMNIS Dosing Drive Unit, with the attached OMNIS cylinder unit, performs precise dosing steps. The intelligent partial-loop injection technique allows calibration using a single standard solution because the injection volume can be freely selected. The same applies to sample injection: a small injection volume can be chosen for a highly concentrated sample, or a larger one for low-concentration samples.Prerequisites:OMNIS IC S/M/L with OMNIS IC AS/ASCOOL, including:available OMNIS Dosing Drive Unit; available OMNIS MISP Unit;

6.05331.080

Accessory set for the combination of Partial Loop Injection Technique with Ultrafiltration in OMNIS IC: The inline ultrafiltration allows the sample to be separated from contained particles. Additionally, with the partial loop injection, the 250 μL sample loop can be filled with a defined volume of the filtered sample. The OMNIS Dosing Drive Unit, with the attached OMNIS cylinder unit, performs precise dosing steps. This combined technique allows calibration using a single standard solution.Prerequisites:OMNIS IC S/M/L with OMNIS IC AS/ASCOOL, including:available OMNIS Dosing Drive Unit; available OMNIS Peristaltic Pump Unit channel; available OMNIS MISP Unit; AS/ASCOOL equipped with dilution station and switching valve 3/2, UNF;

6.05331.090

Accessory set for manual Full Loop Injection in OMNIS IC: With this technique, the sample loop can be filled manually.Prerequisites:OMNIS IC S/M/L

6.05332.000

Accessory set for automatic monitoring of 10 L container.Prerequisites:OMNIS IC with ROLC

6.05332.010

Accessory set for connecting drain to 10 L container.Prerequisites:OMNIS IC S/M/L

6.05332.020

Accessory set for HPP piston seal wash: The HPP piston seal wash for the OMNIS IC HPP is standard foreseen with a free port on a dosing system on the OMNIS Cylinder Unit. After each sample analysis, the piston is rinsed with a small portion of UPW.When no free Cylinder Unit channel is available, the UPW can alternatively be transferred via a peristaltic pump channel equipped with 601826010 peristaltic pump tubing.Prerequisites:OMNIS IC S/M/L, including:available OMNIS Cylinder Unit port (with UPW as working medium) or; available OMNIS Peristaltic Pump Unit channel;

6.05332.040

Accessory set for MSM regeneration with Peristaltic Pump Unit.Prerequisites:OMNIS IC S/M/L, including:available OMNIS Peristaltic Pump Unit channel;

6.05332.050

Accessory set for MSM regeneration with Dosing Drive Unit with STREAM setup.Prerequisites:OMNIS IC S/M/L, including:available OMNIS Dosing Drive Unit;

6.05332.060

Accessory set for an OMNIS IC without OMNIS IC AS or ASCOOL: With this equipment, the OMNIS IC (S/M/L) can be provided as a standalone solution without automation below the IC. This equipment is also required when the OMNIS IC is used in combination with an 858 Professional Sample Processor or a 919 IC Autosampler plus.Prerequisites:OMNIS IC S/M/L without AS/ASCOOL automation

6.05332.070

Accessory set for PCR in OMNIS IC: PCR-UV/VIS detection is used to photometrically detect analytes through a chemical reaction following chromatographic separation. In the PCR cartridge, the eluent is mixed with a reagent behind the separation column, thereby enabling a specific reaction with the analyte. The eluent-reagent mixture, along with the reacted analytes, is then transported to the UV detector. This set is specific for the PCR application in combination with the dosing drive unit, including an additional bottle for rinsing purposes.Prerequisites:OMNIS IC S/M/L, including:available OMNIS Dosing Drive Unit; available OMNIS Column Thermostat Unit;

6.05332.080

Accessory set for automatic eluent production in OMNIS IC.Prerequisites:OMNIS IC S/M/L including:available OMNIS Dosing Drive Unit;

6.05332.090

Accessory set for Dose-in Gradient in OMNIS IC: A gradient is created by mixing different eluents in a mixing ratio that varies over the analysis duration.An OMNIS Cylinder Unit doses a concentrated or diluted eluent into the main eluent stream in a defined ratio. This changes the overall concentration of the mobile phase. The result is optimal separation of all ions within an acceptable analysis time.Prerequisites:OMNIS IC S/M/L, including:available OMNIS Dosing Drive Unit;

6.05332.100

Accessory set for MSM regeneration with Dosing Drive Unit without STREAM setup.Prerequisites:OMNIS IC S/M/L, including:available OMNIS Dosing Drive Unit;

6.05332.110

Accessory set for PCR in OMNIS IC: PCR-UV/VIS detection is used to photometrically detect analytes through a chemical reaction following chromatographic separation. In the PCR cartridge, the eluent is mixed with a reagent behind the separation column, thereby specifically reacting with the analyte. The eluent-reagent mixture, along with the reacted analytes, is then transported to the UV detector. This set is specific for the PCR application in combination with the peristaltic pump unit.Prerequisites:OMNIS IC S/M/L, including:available OMNIS Peristaltic Pump Unit channel; available OMNIS Column Thermostat Unit;

6.05332.120

Accessory set for an OMNIS IC without OMNIS IC AS or ASCOOL: If the OMNIS IC system is to be set up in 2 stacks (two-tower setup), the OMNIS IC must be equipped with a base plate, and the AS/ASCOOL with a reagent organizer.Prerequisites:OMNIS IC S/M/L

6.05332.130

Accessory set for AutoSwitch in OMNIS IC: Many samples require analysis of multiple analytes, such as anions and cations. The OMNIS IC M can be easily upgraded to perform AutoSwitch analysis. This enables automated serial execution, for example, of anion and cation analyses. Automatic switching between different analyses is possible with an additional injector and two 3/2-way valves.Prerequisites:OMNIS IC M, including:available OMNIS Actuator Unit equipped with 6/2 or 7/3 injector (minimum 1 x 7/3 injector is required); available position on the OMNIS Column Thermostat Unit; AS/ASCOOL equipped with 1x switching valve 3/2, M6 and 1x switching valve 3/2, UNF;

6.05801.000

Upgrade kit to extend the OMNIS Peristaltic Pump Unit 1-Channel with an additional pump channel.Prerequisites:2.1056.0010 OMNIS Peristaltic Pump Unit 1-Channel; Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.010

Upgrade kit to extend the OMNIS High-Pressure Pump Unit with piston wash. Piston wash seals are included.Prerequisites:2.1056.0210 OMNIS High-Pressure Pump Unit; 6.02621.010 Multitool, HPP;

6.05801.020

Upgrade kit to extend the OMNIS IC Degasser Unit with an additional degasser channel.Prerequisites:OMNIS IC S/M/L, including:2.1056.0010 OMNIS Degasser Unit 1-Channel or; 2.1056.0020 OMNIS Degasser Unit 2-Channel; Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.040

Upgrade kit to extend the OMNIS Reagent Organizer Liquid Control with an additional volume sensor.Prerequisites:2.1056.1200 OMNIS Reagent Organizer Liquid Control; Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.050

Spare part: OMNIS IC Door 1. The necessary hinges are included.

6.05801.060

Spare part: OMNIS IC Door 2. The necessary hinges are included.

6.05801.070

Spare part: OMNIS IC Door 3. The necessary hinges are included.

6.05801.080

Spare part: OMNIS IC Door 4. The necessary hinges are included.

6.05801.090

Upgrade kit to extend the OMNIS Reagent Organizer Liquid Control with a magnetic stirrer. Prerequisites: 2.1056.1200 OMNIS Reagent Organizer Liquid Control; Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.110

The switching valve 3/2 is a valve with 3 connectors and 2 switching positions. The switching valve 3/2 is available with either a valve attachment with UNF 10/32 connectors or one with M6 connectors.It can be used for the following applications, for example:Anion/cation system: Control as to the channel into which the sample is injected.; Rinsing with 2 different solutions: Control as to which rinsing solution is used.; A maximum of 3 switching valves 3/2 can be installed per sample changer.Note: This upgrade must be installed by an authorized Metrohm service engineer.

6.05801.120

The switching valve 3/2 is a valve with 3 connectors and 2 switching positions. The switching valve 3/2 is available with either a valve attachment with UNF 10/32 connectors or one with M6 connectors.It can be used for the following applications, for example:Anion/cation system: Control as to the channel into which the sample is injected.; Rinsing with 2 different solutions: Control as to which rinsing solution is used.; A maximum of 3 switching valves 3/2 can be installed per sample changer.Note: This upgrade must be installed by an authorized Metrohm service engineer.

6.05801.130

The individual sample racks and the AS tray are each identified with a barcode. The barcode reader scans the barcodes. This way, the sample changer detects the number, the position, and the type of the sample racks currently present. In addition, the barcode reader detects empty rack positions.Note: This upgrade must be installed by an authorized Metrohm service engineer.

6.05801.170

Upgrade kit to extend the OMNIS Actuator Unit with a metal-free 6/2 injector with UNF 10/32 connections. Injector specifications: Bore ID: 0.4 mm; Rotor material: Valcon E; Stator material: PAEK/Carbon Fiber; Maximum pressure: 35 MPa; Prerequisites:210560410 OMNIS Actuator Unit Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.180

Upgrade kit to extend the OMNIS Actuator Unit with a metal-free 7/3 injector with UNF 10/32 connections. Injector specifications: Bore ID: 0.4 mm; Rotor material: Valcon E; Stator material: PAEK/Carbon Fiber; Maximum pressure: 35 Mpa; Prerequisites: 2.10560.410 OMNIS Actuator Unit Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.190

Upgrade kit to extend the OMNIS Actuator Unit with a metal-free 4/2, 0.25µL internal loop injector with UNF 10/32 connections.Injector specifications:Bore ID: 0.4 mm; Rotor material: Valcon E; Stator material: PAEK/Carbon Fiber; Maximum pressure: 24 MPa; Prerequisites:210560410 OMNIS Actuator UnitInfo: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.200

Upgrade kit to extend the OMNIS Actuator Unit with a metal-free 4/2, 1.0 µL internal loop injector with UNF 10/32 connections. Injector specifications: Bore ID: 0.4 mm; Rotor material: Valcon E; Stator material: PAEK/Carbon Fiber; Maximum pressure: 24 MPa; Prerequisites: 210560410 OMNIS Actuator Unit Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.210

Upgrade kit to extend the OMNIS Actuator Unit with a metal-free 8/2 injector with UNF 10/32 connections. Injector specifications: Bore ID: 0.4 mm; Rotor material: Valcon E; Stator material: PAEK/Carbon Fiber; Maximum pressure: 35 Mpa; Prerequisites: 210560410 OMNIS Actuator Unit Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.220

Upgrade kit to extend the OMNIS Actuator Unit with a metal-free 10/2 injector with UNF 10/32 connections.Injector specifications:Bore ID: 0.4 mm; Rotor material: Valcon E; Stator material: PAEK/Carbon Fiber; Maximum pressure: 35 Mpa; Prerequisites:210560410 OMNIS Actuator UnitInfo: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.230

Upgrade kit to extend the OMNIS Actuator Unit with a metal-free 10/1 Selector, low-pressure with UNF 10/32 connections. Injector specifications: Bore ID: 0.75 mm; Rotor material: Valcon E; Stator material: PPS; Maximum pressure: 2 Mpa; Prerequisites: 210560410 OMNIS Actuator Unit Info: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.240

Upgrade kit to extend the OMNIS Actuator Unit with a metal-free 10/1 Selector, low-pressure with UNF 10/32 connections.Injector specifications: Bore ID: 0.4 mm; Rotor material: Valcon E; Stator material: PAEK/Carbon Fiber; Maximum pressure: 35 Mpa; Prerequisites:210560410 OMNIS Actuator UnitInfo: This upgrade must be installed by an authorized Metrohm service technician.

6.05801.250

The dilution station is used for automatic dilution of samples. A defined amount of the concentrated sample is precisely measured by an OMNIS Dosing Drive Unit. The concentrated sample is conveyed to the dilution vessel with the required volume of the dilution solution. The built-in magnetic stirrer mixes the concentrated sample and the dilution solution evenly. The diluted sample is then transferred through the sample outlet into the sample path.Metrohm recommends using the following stirring bar:Stirring bar / 8 x 3 mm (6.1903.000); The dilution station is equipped with an overflow. The liquid in the overflow is collected in the drip collector, runs from there to the leak sensor, and is then fed into the drainage tubing system.A maximum of 1 dilution station can be installed per sample changer. If contaminated, the dilution vessel can be cleaned or replaced.Note: This upgrade must be installed by an authorized Metrohm service engineer.

6.05801.260

Drain kit to replace the drain tubing and connections in the OMNIS IC Autosampler Module.Prerequisites: 2.1054.0010 OMNIS IC Autosampler Module

6.05801.270

Drain kit to replace the drain tubing and connections in the OMNIS IC Autosampler COOL.Prerequisites:2.1054.0020 OMNIS IC Autosampler Module COOL

6.05801.280

Drain kit to replace the drain tubing and connections in the OMNIS IC S. Prerequisites: 2.1050.00x0 OMNIS IC S

6.05801.290

Drain kit to replace the drain tubing and connections in the OMNIS IC M.Prerequisites:2105100x0 OMNIS IC M

6.05801.310

Drain kit to replace the drain tubing and connections in the OMNIS IC L.Prerequisites:2105200x0 OMNIS IC L

6.05801.330

Upgrade kit to extend the OMNIS IC S/M/L with a mobile device holder.Prerequisites:OMNIS IC S/M/LInfo: This upgrade must be installed by an authorized Metrohm service technician.

6.2743.100

Maximize sample recovery with this 0.7 mL vial designed for low-volume analytical applications. The vial features a low-dead-volume insert design that enables efficient sample extraction while minimizing waste. Quantity: 1000 pieces

6.2743.107

Maximize sample recovery with this 0.7 mL vial designed for low-volume analytical applications. The vial features a low-dead-volume insert design that enables efficient sample extraction while minimizing waste. Quantity: 100 pieces

6.2743.110

Maximize sample recovery with this 0.3 mL vial designed for low-volume analytical applications. The vial features a low-dead-volume insert design that enables efficient sample extraction while minimizing waste. Quantity: 1000 pieces

6.2743.117

Maximize sample recovery with this 0.3 mL vial designed for low-volume analytical applications. The vial features a low-dead-volume insert design that enables efficient sample extraction while minimizing waste. Quantity: 100 pieces

6.2743.120

Snap cap with septum for 11 mm vials. Provides reliable sealing and broad chemical compatibility for routine laboratory analysis Quantity: 1000 pieces

6.2743.127

Snap cap with septum for 11 mm vials. Provides reliable sealing and broad chemical compatibility for routine laboratory analysis Quantity: 100 pieces

6.7303.100

Maximize sample recovery with this universal 1.8 mL snap ring vial designed for low-volume analytical applications. Quantity: 100 pieces

6.7303.110

Snap cap with septum for 11 mm vials. Provides reliable sealing and broad chemical compatibility for routine laboratory analysis. Quantity: 100 pieces

BWT-840000961

Video microscope sampling system for use with B&W Tek's lab and industrial Raman probes. Includes a 20x objective at a working distance of 16 mm. Offers manual rough and fine adjustment on the X, Y, and Z-axes, coaxial LED illuminator for target alignment, video camera for sample observation, and is compatible with standard microscope objectives. Probe not included, available separately. 785 nm configuration.BAC151C-785

DRP-CAST

Connects any DropSens equipment with DropSens Screen-Printed Electrodes

DRP-CNFSOL-1ML

Carbon Nanofibres Solution produced via the catalytic carbon vapour deposition process. The manufacturing processes provide a highly graphitized material without amorphous carbon – Available in 1.0 mL and 5.0 mL.

DRP-FLWCL

Methacrylate wall-jet Flow-Cell for FIA. Suitable to be used with standard format Screen-Printed Electrodes with the electrochemical cell in the middle of the strip. Closing system with powerful magnets Fittings included.

EC.Raman.Battery

An Autolab modular PGSTAT302N with an Electrochemical Impedance Spectroscopy (EIS) module installed and a B&W Tek i-Raman Plus 532 H System are the foundation of this system. Depending on your cell size and design you can add either a B&W Tek Raman Video Micro-Sampling System (532 nm), or the B&W Tek Raman Probe Holder.Get ready to track age-induced structural changes, electrolyte decomposition, and solid electrolyte interphase (SEI) formation with your EC-Raman Battery Solution.It is easy to get started, see instant results, all with an instrument you can upgrade as your research progresses.• Two editable hyphenated EC-Raman procedures for the NOVA software as well as the BWSpec software for extended data analysis.• An electrochemical workstation with high accuracy EIS.• Future-proof your research with the ability to add up to 7 additional modules post-installation.Choose, depending on your cell size, either a B&W Tek Raman Video Microsampling System (532 nm), or the B&W Tek Raman Probe Holder.B&W Tek Raman Video Microsampling System (532 nm) can accommodate cells up 30 mm high.B&W Tek Raman Probe Holder can accommodate large battery-dedicated EC-Raman cells.

DRP-BICAST

Connects any DropSens equipment with DropSens Dual Screen-Printed Electrodes

DRP-CNTSOL-0.5ML

Carbon nanotubes are produced via CVD and purified to remove free amorphous carbon deposits and catalyst metallic particles. They are functionalized with -COOH groups - Available in 1.0 mL and 5.0 mL.

EC.Raman.Corrosion.Explorer

Includes an Autolab modular PGSTAT302N with an Electrochemical Impedance Spectroscopy (EIS) module installed, a B&W Tek i-Raman Plus 532 H System, a B&W Tek Raman Video Microsampling System (532 nm) and an Autolab Trigger cable.Ready when you are, the EC-Raman Explorer Corrosion Solution is easy to use. Get started quickly with a versatile potentiostat/galvanostat that can be expanded as your research develops.• Two editable hyphenated EC-Raman procedures for the NOVA software as well as the BWSpec software for extended data analysis.• An electrochemical workstation with high accuracy EIS.• Future-proof your research with the ability to add up to 7 additional modules post-installation.• 532 nm laser excitation for higher Raman signal• Visual surface inspection with the microsampling system

DRP-CABSTAT1

Connects individual nodes of the μStat 8000(P)/4000(P) to conventional electrodes

DRP-FLWCL-PEEK

PEEK wall-jet Flow-Cell for FIA. Suitable to be used with standard format Screen-Printed Electrodes with the electrochemical cell in the middle of the strip. Closing system with powerful magnets. Fittings included.

DRP-GPHSOL-1ML

Graphene Solution - Available in 1.0 mL and 5.0 mL.

EC.Raman.ECAT.Explorer

Includes an Autolab modular PGSTAT302N with an Electrochemical Impedance Spectroscopy (EIS) module installed, a B&W Tek i-Raman Plus 532 H System, a B&W Tek Raman Video Microsampling System (532 nm) and an Autolab Trigger cable.Synchronize your electrochemical measurements with in situ Raman spectroscopy providing:• Simultaneous structural and functional information about your catalysts• Operando measurements allow for tracking changes of the catalyst structure, identifying adsorbed products or intermediates• A powerful modular potentiostat/galvanostat with current ranges from 10 nA to 1 A.• An electrochemical workstation with high accuracy EIS.• Two editable hyphenated EC-Raman procedures for the NOVA software as well as the BWSpec software for extended data analysis.• Future-proof your research with the ability to add up to 7 additional modules post-installation.• 532 nm laser excitation for higher Raman signalAll without complicated setups or complex training.

DRP-CAST8X

Connects μStat 8000(P) equipment to 8X format Screen-Printed Electrodes

DRP-FLWCL-P

Polypropylene wall-jet Flow-Cell for FIA. Suitable to be used with standard format Screen-Printed Electrodes with the electrochemical cell in the middle of the strip. Closing system with powerful magnets. Fittings included.

EC.Raman.Corrosion.Starter

Includes a compact Autolab PGSTAT204 with an Electrochemical Impedance Spectroscopy (EIS) module installed, a B&W Tek i-Raman Plus 532 H System, a B&W Tek Raman Video Micro-Sampling System (532 nm) and an Autolab Trigger cable.Get started quickly and have a dual perspective on corrosion phenomena. The EC-Raman Starter Corrosion Solution provides you with the instrumentation you need to get started.• Two editable hyphenated EC-Raman procedures for the NOVA software as well as the BWSpec software for extended data analysis.• An electrochemical workstation with high accuracy EIS.• Ready-to-go and simple to use.• 532 nm laser excitation for higher Raman signal• Visual surface inspection with the microsampling system

BWT-810000682

External Lithium-Ion battery that provides constant 12 VDC. (Compatible with the i-Raman-Plus, i-Raman Pro and i-Raman EX models).EBP106

DRP-CAST1X8

Connects μStat 8000(P) equipment with individual Screen-Printed Electrodes