Filtro de Aplicações

In this poster a convenient direct injection suppressed ion chromatographic method for determining chloride and sulfate in denatured ethanol samples according to ASTM D7319 is presented.

Quality and process control of biofuels require straightforward, fast and accurate analysis methods. Ion chromatography (IC) is at the leading edge of this effort. Traces of anions in a gasoline/ethanol blend can accurately be determined in the sub-ppb range after Metrohm Inline Matrix Elimination using anion chromatography with conductivity detection after sequential suppression. While the analyte anions are retained on the preconcentration column, the interfering organic gasoline/bioethanol matrix is washed away.Detrimental alkali metals and water-extractable alkaline earth metals in biodiesel are determined in the sub-ppm range using cation chromatography with direct conductivity detection applying automated extraction with nitric acid and subsequent Metrohm Inline Dialysis. Unlike high-molecular substances, ions in the high-ionic strength matrix diffuse through a membrane into the low-ionic water acceptor solution. In biogas reactor samples, low-molecular-weight organic acids stem from the biodegradation of organic matter. Their profile allows important conclusions concerning conversion in the anaerobic digestion reaction. Volatile fatty acids and lactate can be accurately determined by using ion-exclusion chromatography with suppressed conductivity detection after inline dialysis or filtration.

The combination of 850 Professional IC, 858 Professional Sample Processor, Dosino and MagIC NetTM software offers a variety of sophisticated ion chromatographic sample preparation techniques. One of these is the automated inline dilution of samples.After the first sample injection, MagIC NetTM verifies if the area of the sample peak lies within the calibration range. If the measured peak area is outside these limits, the software calculates the appropriate dilution factor, dilutes and automatically re-injects the sample. For all investigated ions (Li+, Na+, K+, Ca2+, Mg2+, F-, Cl- , NO2-, Br-, NO3-, SO42- ), automated logical dilution yielded coefficients of determination (R2) better than 0.9999. Direct-injection recoveries for cations and anions were within 98.6…99.5% and 93.4…100.4% respectively. In contrast, after logical dilution, recoveries for cations and anions were within 100.1…102.9% and 98.2…102.6% respectively. The relative standard deviations for all determinations involving diluted sample solutions were smaller than 0.91%.

The analytical challenge treated by the present work consists in detecting sub-ppm quantities of bromide, sulfate, aliphatic monocarboxylic acids and several alkaline earth metals in the presence of very high concentrations of sodium and chloride. Bromide, sulfate, acetate and butyrate can be reliably determined by suppressed conductivity detection. Due to matrix effects, propionate can only be detected qualitatively. This drawback can be overcome by coupling the ion chromatograph (IC) to a mass spectrometric (MS) detector. This results in reduced matrix interferences and significantly enhanced sensitivities. The cations magnesium, barium and strontium are determined by non-suppressed conductivity detection.

The study of adverse effects of air pollution requires semi-continuous, rapid and accurate measurements of inorganic species in aerosols and their gas phase components in ambient air. The most promising instruments, often referred to as steam collecting devices, are the Particle-Into-Liquid-Sampler (PILS) coupled to wet-chemical analyzers such as a cation and/or anion chromatograph (IC) and the Monitoring instrument for AeRosols and GAses (MARGA) with two integrated ICs. Both instruments comprise gas denuders, a condensation particle growth sampler as well as pump and control devices. While PILS uses two consecutive fixed denuders and a downstream growth chamber, the MARGA system is composed of a Wet Rotating Denuder (WRD) and a Steam-Jet Aerosol Collector (SJAC). Although the aerosol samplers of PILS and MARGA use different assemblies, both apply the technique of growing aerosol particles into droplets in a supersaturated water vapor environment. Previously mixed with carrier water, the collected droplets are continuously fed into sample loops or preconcentration columns for on-line IC analysis. While PILS has been designed to sample aerosols only, MARGA additionally determines water-soluble gases. Compared to the classical denuders, which remove gases from the air sample upstream of the growth chamber, MARGA collects the gaseous species in a WRD for on-line analysis. In contrast to the gases, aerosols have low diffusion speeds and thus neither dissolve in the PILS denuders nor in the WRD. Proper selection of the ion chromatographic conditions of PILS-IC allows a precise determination, within 4 to 5 minutes, of seven major inorganic species (Na+, K+, Ca2+, Mg2+, Cl-, NO3- and SO4 2-) in fine aerosol particles. With longer analysis times (10-15 minutes) even airborne low-molecular-weight organic acids, such as acetate, formate and oxalate can be analyzed. MARGA additionally facilitates the simultaneous determination of HCl, HNO3, HNO2, SO2 and NH3.PILS and MARGA provide semi-continuous, long-term stand-alone measurements (1 week) and can measure particulate pollutants in the ng/m3 range.

The analytical challenge treated in the present work consists in detecting trace concentrations (ppb) of bromide in the presence of a strong chloride matrix. This problem was overcome by separating the bromide ions from the main fraction of the early eluting chloride matrix (several g/L) by applying two sequential chromatographic separations on the same column. After the first separation, the main fraction of the interfering chloride matrix is flushed to waste, while the later eluting anions are diverted to an anion-retaining preconcentration column. After elution in counter flow, the bromide ions are efficiently separated from the marginal chloride residues. The four-point calibration curves for bromide and sulfate are linear in the range of 10…100 µg/L and 200…800 µg/L and yield correlation coefficients of 0.99988 and 0.99953 respectively. For the method shown here, a second injection valve and a preconcentration column are the only additional devices needed to master this demanding separation problem.

Several testing methods such as the determination of the acid and the iodine numbers in biodiesel as well as the quantification of sulfate and chloride in bioethanol are described.

The combination of 850 Professional IC, 858 Professional Sample Processor, Dosino and MagIC NetTM software offers a variety of automated ion chromatographic sample preparation and calibration techniques available as an anion, cation or dual channel system. Calibration is straightforward and requires only one multi-ion standard.Inline calibration allows the calibration of any standard concentration in the ppt range by using one single stable standard solution at the ppb level. By using a preconcentration column and switching the valves one, two or more times different calibration concentrations at the ultra-trace level can be created with unprecedented reproducibility. The inline preconcentration technique uses a pre-concentration column and is ideally suited for trace analysis in complex matrices, especially when combined with matrix elimination. Besides facilitating the preparation of g/L to ng/L calibration graphs Metrohm`s intelligent techniques are capable of logical decision making. While Metrohm`s intelligent Partial Loop technique (MiPT) allows samples with a wide concentration range to be injected without previous manual dilution, the intelligent inline dilution technique, after the first sample injection, compares peak areas, calculates, if necessary, the dilution factor, dilutes and automatically re-injects the sample. The presented inline techniques allow the rationalization of the time-consuming, error-prone and cost-intensive manual preparation of standard solutions. They guarantee that the determined sample concentrations always lie within the calibration range. Higher sample throughputs as well as lower analysis costs and improved data reliability are achieved.

The analytical challenge treated in the present work consists in the determination of chloride, phosphate and sulfate in the presence of difficult sample matrices that interact with the stationary column phase or even render it unusable. Metrohm`s patented stopped-flow dialysis coupled to the new 881 Compact IC pro ion chromatograph overcomes these drawbacks. Two standard solutions covering the concentration ranges 1.0…3.6 mg/L and 10…36 mg/L as well as two samples, an ultra-high temperature (UHT) processed milk and a baby milk powder, were characterized in terms of analyte concentration, relative standard deviation, calibration quality, carryover and recovery rates. While the five-point calibration curves yielded correlation coefficients (R) better than 0.9999, carryover (between two subsequent injections of a concentrated sample and a blank) was less than 0.49%. Recoveries for the low (10…36 mg/L) and high standard concentrations (1.0…3.6 mg/L) were within 91…99% and 94…100%, respectively. Automated compact stopped-flow dialysis is a leading-edge sample preparation technique that ensures optimum separation performance by effectively protecting the column from detrimental matrix compounds.

Inline coupling of the 815 Robotic Soliprep with an ion chromatograph (IC) allows the straightforward determination of anions and cations in tablets. After automatic solvent addition and subsequent comminution, the homogenized tablet samples (Singulair and Bezafibrat) are filtered and subsequently transferred to the injector. The completely automated sample preparation saves both time and money, guarantees traceability of each sample preparation step and yields correct and precise results. In the range of 0.2…50 mg/L, six-point calibration curves for anions and cations yield correlation coefficients better than 0.99990 and 0.99991, respectively. While relative standard deviations (RSDs) for sub-ppm levels of nitrate, sulfate, calcium and magnesium in Singulair and Bezafibrat are smaller than 3.64%, RSD of ppm levels of chloride is better than 0.83%. The application of further inline sample preparation steps such as pulverizing, extracting, filtering or diluting facilitates numerous custom-tailored setups for ion determinations in exacting matrices such as animal feed, sediments or food.

This poster provides an overview of ion chromatographic methods combined with inline sample preparation for the determination of anions and water-extractable cations in biofuels. In addition, the determination of the oxidation stability is described.

This study compares air sampling data obtained by a filter-based method including off-line manual filter extraction followed by ion chromatographic analysis with those gained by an automated Particle-Into-Liquid-Sampler coupled to an ion chromatograph (PILS-IC).PILS-IC is a straightforward instrument for aerosol sampling that provides near real-time measurements for long-term unattended operation and is thus an indispensable tool to monitor rapid changes in aerosol particle ionic composition.

Available sample size, mass sensitivity, efficiency and the detector type are important criteria in the selection of separation column dimensions. Compared to conventional 4 mm i.d. columns, microbore columns excel, above all, by their low eluent consumption. Once an eluent is prepared, it can be used for a long time. Additionally, the lower flow rates of microbore columns facilitate the hyphenation to mass spectrometers due to the improved ionization efficiency in the ion source.With the same injected sample amount, a halved column diameter involves a lower eluent flow and results in an approximate four-fold sensitivity increase. In a converse conclusion, this means that with less sample amount, microbore columns achieve the same chromatographic sensitivity and resolution than normal bore columns. This makes them ideally suited for samples of limited availability.

Metrohm`s intelligent Preconcentration Technique with Matrix Elimination (MiPCT-ME) excels in its capacity to perform automatic ion chromatographic determinations over 6 orders of magnitude. Crucial requirements for this are the system`s intelligence and the exact measurement of the sample volume. While the intelligence allows to compare results and take decisions, the dosing device takes over the high-precision liquid handling of even single-digit microliter volumes to the preconcentration column. By using only one analytical setup and without additional rinsing, samples containing both ultratraces and high concentrations can be analyzed.As the other Metrohm Inline Techniques, the MiPCT-ME technique presented reduces the workload, ensures complete traceability, is free of carryover effects and significantly improves accuracy and reproducibility of the results.

The poster presents the ion chromatographic determination of organic degradation products such as glycolate, formate and acetate besides the standard anions fluoride, chloride, nitrate and sulfate.

Determination of chloride and sulfate in the presence of high nitrate concentrations. Optimization of the chromatographic separation by variation of the temperature and eluent composition.

Three different suppressor systems are compared in terms of sensitivity. Additionally, binary gradient elution was applied to analyze phosphates in the presence of mono- and divalent ions.

The poster describes how different suppressors (MSM and MCS) work and mentions possible applications.

This poster presents an approach that couples a Particle-Into-Liquid-Sampler (PILS) to a dual-channel ion chromatograph (IC) for measurement of aerosol anions and cations and a voltammetric measuring stand (VA) to determine the heavy metals. Feasibility of the PILS-IC-VA online system was demonstrated by collecting aerosol samples in Herisau Switzerland, at defined time intervals; air pollution events were simulated by burning lead- and cadmium-coated sparklers.

The Combustion IC system presented allows the automated determination of organic halogen and sulfur compounds in all flammable samples. Both combustion digestion, which is automatically controlled with a flame sensor, and the professional Liquid Handling guarantee highest precision and trueness. This poster describes the determination of the halogen and sulfur content in a certified polymer standard, a coal reference material as well as in latex and vinyl gloves.

This poster presented jointly with USP at AAPS meeting shows, that we successfully validated an IC method to determine chloride and sulfate in drug substances, potassium bicarbonate and potassium carbonate. The proposed IC method overcomes limitations of the turbidimetry/visual comparison methods.

If chloride and bromide are present in approximately equal molar concentrations they can be titrated directly with silver nitrate solution after addition of barium acetate. If, however, the molar ratio n(Br-) : n(Cl-) changes from 1 : 1 to 1 : 5, 1 : 10, 5 : 1 or 10 : 1 then greater relative errors must be expected with this method. The Bulletin describes an additional titration method that allows bromide to be determined in the presence of a large excess of chloride. The determination of small chloride concentrations in the presence of a large excess of bromide is not possible by titration.

The quality of egg-based pasta is primarily determined by its egg content. Also of importance, however, is the water content, which influences the storage life of the product, as well as the degree of acidity which, in the case of high values, indicates undesirable acidification during processing or drying. A check of the chloride content shows whether salt has been added to the pasta.

This Bulletin describes analysis methods for determining the following parameters: pH value, total titratable acid, ash alkalinity, formol number, total sulfurous acid, chloride, sulfate, calcium, and magnesium. These methods are suitable for the analysis of jams, fruit and vegetable juices, and their concentrates.

This Bulletin describes potentiometric titration methods for the determination of the acidity in milk and yoghurt according to DIN 10316, ISO/TS 11869, IDF/RM 150, ISO 6091 and IDF 86, the chloride content in milk, butter and cheese according to EN ISO 5943, IDF 88, ISO 15648, IDF 179, ISO 21422, and IDF 242. Additionally the determination of the sodium content in milk using the thermometric titration is described. The determination of the oxidation stability of butter in accordance to AOCS Cd 12b-92, ISO 6886 and GB/T 21121 as well as the determination of lactose in lactose free milk by ion chromatography is also described.For the determination of the pH value in dairy products see Application Bulletin AB-086 and for the determination of calcium and magnesium see Application Bulletin AB-235.

This Bulletin describes potentiometric titration methods for checking sulfuric acid and chromic acid anodizing baths. In addition to the main components aluminum, sulfuric acid, and chromic acid, chloride, oxalic acid, and sulfate are determined.

Potentiometric titration methods for the analysis of acid and alkaline tin plating baths are presented. The following methods are described: tin(II) / tin(IV) / total tin, free fluoroboric acid, or free sulfuric acid, chloride in acidic tin baths, free hydroxide, and carbonate in alkaline tin baths.

Besides acid-base titrations, the titrimetric determination of chloride is one of the most frequently used titrimetric methods of analysis. It is employed more or less frequently in practically every laboratory. This Bulletin shows you how to determine chloride in a wide range of concentrations using automatic titrators. Silver nitrate is normally used as titrant (for environmental reasons one should refrain from using mercury nitrate). The titrant concentration depends on the chloride content of the sample to be analyzed. It is crucial to choose the correct electrode for samples with low chloride contents.

The determination of the physical and chemical parameters as electrical conductivity, pH value, p and m value (alkalinity), chloride content, the calcium and magnesium hardness, the total hardness, as well as fluoride content are necessary for evaluating the water quality. This bulletin describes how to determine the above mentioned parameters in a single analytical run. Further important parameters in water analysis are the permanganate index (PMI) and the chemical oxygen deman (COD). Therefore, this Bulletin additionally describes the fully automated determination of the PMI according to EN ISO 8467 as well as the determination of the COD according to DIN 38409-44.

This Bulletin gives a survey of standard methods from the field of water analysis. You will also find the analytical instruments required for the respective determinations and references to the corresponding Metrohm Application Bulletins and Application Notes. The following parameters are dealt with: electrical conductivity, pH value, fluoride, ammonium and Kjeldahl nitrogen, anions and cations by means of ion chromatography, heavy metals by means of voltammetry, chemical oxygen demand (COD), water hardness, free chlorine as well as a few other water constituents.

This Bulletin describes the determination by ion chromatography of anions, particularly fluoride, chloride, nitrite, bromide, nitrate, and sulfate using the Hamilton PRPX100 IC anion column without chemical suppression.

Bethanechol is a pharmaceutical compound which is used to treat urinary retention. This API (active pharmaceutical ingredient) can be determined by cation chromatography with direct conductivity detection. A good separation is achieved between bethanechol and its degradation product 2-hydroxy-propyl-trimethyl ammonium (HPTA) and the standard cations. Peak shape and resolution meet the USP requirements for bethanechol.

A queima de carvão contamina a atmosfera com halogênios. Flúor e cloro são componentes naturais do carvão, enquanto o brometo encontrado neles é frequentemente adulterado como brometo de cálcio para reduzir as emissões de mercúrio. Esta Nota de Aplicação mostra os resultados da digestão por combustão com o Combustion IC para três amostras de carvão, cada uma com um teor de brometo diferente. Palavra-chave: pirohidrólise

Halobutyl rubber is frequently used in the production of pharmaceutical stoppers. It is ideal for this application due to its low permeability to gases and its chemical resistance. Chlorinated and brominated butyl rubber stoppers are analyzed for their halogen and sulfur content. Halogen and sulfur compounds are released by pyrohydrolysis and analyzed by subsequent ion chromatography (IC).

O teor de cloreto orgânico no petróleo bruto é determinado de acordo com a norma ASTM D8150 na fração nafta após a destilação. A fração de nafta é lavada com soda cáustica e água, respectivamente, para remover sulfeto de hidrogênio e haletos inorgânicos. Aqui, é apresentada a determinação de cloreto orgânico após combustão em linha. Embora o teor de enxofre não tenha interesse nesta aplicação, a mesma configuração permite a quantificação de enxofre.

Polymer materials that are used for building and decoration purposes need to be flame resistant. To reach the required level of resistance flame-retardants are added to the plain polymer. Flame-retardants are often haloorganic compounds. The use of such components and the respective concentration of introduced halogens can be determined by Combustion IC. The recovery over the full system is tested with a certified reference material (CRM).

O minério de ferro é um recurso importante para a produção de aço. Seu conteúdo natural de halogênios é uma característica de qualidade devido à corrosividade dos respectivos halogenetos. O CI de combustão que aplica a tecnologia de frasco de sacrifício é usado para a análise de flúor e cloro no minério. OS3 geralmente é adicionado para melhorar a liberação de SO2 e, portanto, recuperação de enxofre. Nesta aplicação, também melhora significativamente a recuperação de flúor.

As folhas de éster de celulose são produzidas usando solventes clorados. A quantidade residual do solvente usado na produção evapora em poucos dias em condições ambientais. O solvente residual é determinado pela combustão IC, através da conversão de cloro organicamente ligado em cloreto por piroidrólise. O produto final precisa estar livre de solventes clorados. Portanto, conteúdos críticos de tais compostos podem ser detectados na análise de controle de qualidade. A aplicação do MiPT neste estudo permitiu uma calibração automatizada e precisa a partir de um único padrão.

This application focuses on the simultaneous analysis of cations and suppressed anions with a dual channel Metrohm IC operated by OpenLab CDS.

This Application Note presents ion chromatography as a precise method to analyze anions in beer as well as cations with non-suppressed conductivity. Automation with Inline Ultrafiltration is also discussed.

Ion chromatography (IC) provides an automated, fast, and sensitive solution to accurately quantify cationic and anionic components including acetate simultaneously. This comprehensive approach makes IC an economic alternative to traditional techniques for the quality control of pharmaceutical solutions like haemodialysis concentrates. Ease-of use, accuracy, and the high-throughput of IC increase productivity and comply with the demands of modern routine and research labs.

Determinação de brometo e cloreto em soluções reveladoras fotográficas.

Determinação de cloreto em fluidos de perfuração de poços de petróleo.

Determinação de baixos níveis de cloreto (até aproximadamente 5 mg/L Cl-) por titulação termométrica.

Determination of chloride in Bayer process liquor.

Determination of total halides (Cl- + Br- +I-) in seawater and similar brines. This procedure is suitable for the analysis of total halides in seawater contaminated with sodium aluminate solutions emanating from alumina refineries, and seawater which has been used for the neutralization of alumina refinery waste («red mud») slurries. Given the small concentration of bromine andiodine in seawater, the total halide content approximates the chloride concentration.

Determination of chloride in water by direct potentiometry using the Cl-ISE.

In the synthesis of certain dyes, sodium chloride is a byproduct. The content of chloride is therefore an important parameter. This Application Note describes the determination of the chloride content in dye by standard addition using a Cl- ion-selective electrode.

Determination of anions in solder paste after alcoholic extraction using anion chromatography with direct conductivity detection.

Determination of anions in a Schoeniger absorption solution of a test mixture without decomposition of the H2O2 using anion chromatography with direct conductivity detection.

Determination of chloride, nitrate, phosphate, sulfate, and oxalate in dried potatoes using anion chromatography with direct conductometric detection.

Determination of acetate, formate, chloride, bromide, and sulfate in toluene using anion chromatography with direct conductivity detection.

Determination of chloride, nitrate, phosphate and sulfate in plant leaf extracts using anion chromatography with direct conductometric detection.

Determination of chloride, bromide, and iodide in alkaline combustion solutions using anion chromatography with direct conductivity detection.

Determination of acetate, lactate, and chloride in electrolyte solutions using anion chromatography with direct conductivity detection.

Determination of chloride, nitrate, and sulphate in sugar-containing solutions without matrix elimination using anion chromatography with direct conductometric detection.

Determination of fluoride, chloride, nitrite, nitrate, and sulfate in an effluent sample using anion chromatography with direct conductometric detetction.

Determination of fluoride and chloride in gypsum using anion chromatography and subsequent direct conductometric detection.

Determination of acetate, chloride, citrate, and sulfate in a concentrate of an infusion solution using anion chromatography with direct conductivity detection. Non-suppressed IC is used to avoid interferences by the amino acids.

Determination of chloride and sulfate in a reactive dye using anion chromatography with direct conductivity detection. Suppressed IC does not work as the dye is hydrolyzed in alkaline solution and releases sulfate.

Determination of acetate, chloride, and malate in an infusion solution using anion chromatography with direct conductivity detection.

Determination of acetate, phosphate, chloride, and citrate in an infusion solution using anion chromatography with direct conductivity detection.

Determination of chloride and sulfate in effluent after Metrohm Inline Dialysis using anion chromatography with direct conductivity detection.

Automated online analysis with the 2060 TI Ex Proof Process Analyzer facilitates constant monitoring of the crude oil desalting process according to ASTM D3230.

Measures to monitor or prevent corrosion are crucial in nuclear power plants, where significant risks to health and safety can occur if corrosion is left unchecked. Anions corrode metals under high temperature and pressure, therefore their concentrations must be monitored at all times. The analytical challenge in the primary circuit is detection of anions in the μg/L range alongside gram quantities of boric acid and lithium hydroxide. Precise, reliable trace analysis requires the method to be automated as much as possible. The 2060 IC Process Analyzer from Metrohm Process Analytics can measure several anions from a single injection, with combined Inline Preconcentration and Inline Matrix Elimination to measure low anion concentrations precisely and reliably time after time.

The basic chemicals industry is responsible for producing thousands of raw materials at very large scales. The industries downstream rely upon a certain level of chemical purity to manufacture their own goods, as certain impurities can cause major issues in various processes. During the production of the basic chemicals NaOH and KOH, electrolysis of saturated brine solutions with membrane-cells yield the product which is further concentrated by evaporation. Impurities from the salts used in the brine will also be concentrated. Typically, this impurity analysis is performed offline with various hazardous chemicals with varying shelf-lives. The Process Ion Chromatograph is able to perform the measurement described in ASTM E1787-16 online, ensuring quality product without the need for time-consuming, hazardous laboratory experiments.

Determination of trace levels of chloride, nitrate, phosphate, and sulfate in boiler feed water using anion chromatography with conductivity detection after chemical suppression.

A setup that allows online sampling is crucial for immediate and contamination-free analysis of power plant water samples. This application recommends a setup that facilitates simultaneous anion/cation determinations. Automated inline sample preparation combines variable preconcentration (MiPCT) and calibration with a single multi-ion standard. AN-Q-004 displays the respective cation results.

Water of the primary cycle of pressurized water reactors (PWR) contains boron for neutron absorption. The high borate content interferes with the direct analysis of trace anions. Inline Neutralization combined with variable preconcentration and Inline Matrix Elimination (MiPCT-ME) allows to remove boron as boric acid before injection.

A combination of the 850 Professional IC and the 872 Extension Module Liquid Handling opens the field of Metrohm’s online monitoring by IC. In this application, Inline Preconcentration is coupled to Matrix Elimination (MiPCT-ME). By removing excess matrix components, corrosive anions can be sensitively determined. Additionally, this technique allows automated calibration using a single multi-ion standard solution. Online trace analysis for chloride and sulfate is possible for several different sample lines.

The combination of 940 Professional IC Vario, 942 Extension Module Vario LQH and 941 Eluent Preparation Module enables process monitoring with the aid of ion chromatography. Assigned the designation ProfIC Vario 12 Anion, this combination is the anion variant of Metrohm Process IC. Intelligent preconcentration technology with matrix elimination is used for sample preparation. The use of an ELGA PURELAB® Flex 6 guarantees the supply of ultrapure water of the highest quality, particularly in cases of high numbers of samples.

Determination of the anions in potable water using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, nitrate, phosphate, and sulfate in cooling water using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, phosphate, and sulfate in wastewater using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, bromide, nitrate, and sulfate in surface water using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, nitrate, and sulfate in soil eluates using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, bromide, and sulfate in synthetic seawater using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, sulfate, oxalate, and fumarate using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, sulfite, and sulfate in a surfactant solution using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, and nitrate in a solution of NiSO4, ZnSO4 in sulfuric acid using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, bromide, phosphate, and sulfate in an ashed baking additive using anion chromatography with conductivity detection after chemical suppression.

Determination of 1 (3) µg/L of chloride, nitrite, bromide, nitrate, phosphate, and sulfate after direct injection using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, and sulfate in ultrapure water after sample preconcentration using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrate, phosphate, and sulfate in surface water using anion chromatography with conductivity detection after chemical suppression; nitrite with electrochemical detection (conductivity and ELCD detectors in series).

Determination of chloride, nitrite, nitrate, phosphate, and sulfate in cutting oil emulsion using anion chromatography with conductivity detection after chemical suppression and dialysis for sample preparation.

Determination of traces of chloride in a technical product using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, and sulfate in methanol using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, sulfate, chromate, methanesulfonic acid (MSA), methanedisulfonic acid (MDSA), and ethanedisulfonic acid (EDSA) in a chromium plating bath using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, nitrate, and sulfate in rainwater using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, phosphate, and sulfate in boric acid using anion chromatography with conductivity detection after chemical suppression.

Reproducibility of fluoride, chloride, nitrite, bromide, nitrate, and sulfate in the ppb range using anion chromatography with conductivity detection after chemical suppression.

Determination of acetate, chloride, phosphate, and succinate in an infusion solution using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, sulfate, maleate, oxalate, and fumarate in ink using anion chromatography with conductivity detection after chemical suppression and dialysis for sample preparation.

Determination of fluoride, chloride, bromide, and sulfate in bath salts (sea salt) using anion chromatography with conductivity detection after chemical suppression.

Determination of glycolate, acetate, and chloride in monochloroacetic acid (MCA) using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride and sulfate in dust using anion chromatography with conductivity detection after chemical suppression. Sample: dust sample Sample preparation: 0.1 g of dust dissolved in 100 mL c(HNO3) = 0.02 mol/L 0.45 µm filtration

Determination of fluoride, chloride, nitrate, phosphate, and sulfate in boric acid with sample preconcentration using anion chromatography with conductivity detection after chemical suppression.

Determination of traces of fluoride, chloride, nitrate, phosphate, and sulfate in 15% NaOH using anion chromatography with conductivity detection after chemical suppression and inline sample neutralization.

Determination of chloride, bromide, and sulfate in photographic process wastewater using anion chromatography with conductivity detection after chemical suppression.

Determination of acetate, propionate, formate, and chloride in water using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, bromide, and sulfate in seawater using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, chlorate, and sulfate in soda lye (NaOH 50%) after inline neutralization using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, phosphate, and monofluorophosphate in glutamine monofluorophosphate using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrate, sulfite, phosphate, and sulfate in wastewater using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrate, and sulfate in corrosion powder using anion chromatography with conductivity detection after chemical suppression.

Determination of acetate, chloride, nitrate, and sulfate in aluminum oxide using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, phosphate, phosphite, and sulfate in a dye solution using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, bromide, sulfate, and iodide in mineral extracts using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, phosphate, and sulfate in a protein formulation using anion chromatography with conductivity detection after chemical suppression and dialysis for sample preparation.

Determination of gluconate, fluoride, formate, chloride, nitrate, and salicylate using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, bromide, nitrate, phosphate, sulfite, sulfate, and thiosulfate in colored liquors using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride and sulfate in potassium tetraborate (KB4O7 * 4 H2O) using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrite, bromide, nitrate, and sulfate in water for infusion solution production using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, bromide, and sulfate in process wastewater using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrate, phosphate, and sulfate in wastewater using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrite, nitrate, phosphate, and sulfate in an electroplating bath after inline elimination of heavy metals by cation exchange on the 793 IC Sample Prep Module using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrite, bromide, nitrate, phosphate, and sulfate in Schoeniger absorption solution using anion chromatography with conductivity detection after chemical suppression.

Determination of borate and chloride with direct conductivity detection (exhausted MSM). After the introduction of the fresh MSM unit and after the eluent change, sulfate is analyzed with conductivity detection after chemical suppression.

Determination of chloride, nitrate, and sulfate in sodium thiocyanate using anion chromatography with conductivity detection after chemical suppression.

Determination of formate, acetate, chloride, benzoate, and oxalate in phenolic extracts using anion chromatography with conductivity detection after chemical suppression.

Determination of acetate, chloride, sulfate, and citrate in a pharmaceutical product using anion chromatography with conductivity detection after chemical suppression and dialysis for sample preparation.

Determination of fluoride, chloride, phosphate, monofluorophosphate, and sulfate in toothpaste using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, glycolate, monochloroacetate, and chloride in a surfactant solution using anion chromatography with conductivity detection after chemical suppression and dialysis for sample preparation.

Determination of fluoride, glycolate, chloride, and oxalate in a latex dispersion using anion chromatography with conductivity detection after chemical suppression and dialysis for sample preparation.

Determination of chloride, nitrite, nitrate, phosphate, and sulfate in a meat extract (Na2B4O7) after Carrez clearing using anion chromatography with conductivity detection after chemical suppression.

Determination of chlorite, chloride, sulfite, and oxalate in beer using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, bromide, nitrate, phosphate, and sulfate in 20% NaOH after inline neutralization by cation exchange on the 793 IC Sample Prep Module using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, phosphate, sulfate, and oxalate in human urine using anion chromatography with conductivity detection after chemical suppression and dialysis for sample preparation.

Determination of fluoride, chloride, nitrite, nitrate, benzoate, and sulfate in PVC film using anion chromatography with conductivity detection after chemical suppression.

Determination of lactate, acetate, chloride, methylsulfate, bromide, and sulfate using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, bromide, nitrate, phosphate, sulfite, and sulfate in river water using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, phosphate, sulfate, and citrate in beverages using anion chromatography with a high-pressure gradient and conductivity detection after chemical suppression.

Determination of chloride, bromide, nitrate, sulfite, sulfate, phosphate, oxalate, thiosulfate, and thiocyanate (heat stable salts) in scrubber solutions using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride and sulfate in hypophosphoric acid using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride and sulfate in succinic acid using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrite, cyanate, azide, nitrate, chlorate, sulfate, thiocyanate, thiosulfate, and perchlorate in an extract of explosives using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrate, phosphate, sulfate, trimetaphosphate, and tripolyphosphate in tetrasodium pyrophosphate using anion chromatography with a high pressure gradient and conductivity detection after chemical suppression.

Determination of chloride, nitrite, nitrate, phosphate, sulfate, trimeta-, and pyrophosphate in tripolyphosphate using anion chromatography with a high pressure gradient and conductivity detection after chemical suppression.

Determination of bromoacetate, methanesulfonate, chloride, phosphate, and sulfate in an acidic cleaning solution using anion chromatography with conductivity detection and chemical suppression.

Determination of chloride in concentrated nitric acid using anion chromatography with conductivity detection and chemical suppression.

Determination of fluoride, chloride, nitrite, bromide, nitrate, phosphate, sulfate, oxalate, thiosulfate, iodide, and citrate in a standard solution using anion chromatography with a high pressure gradient and conductivity detection after chemical suppression.

Determination of chloride, nitrite, nitrate, and sulfate in cooling lubricants using anion chromatography with conductivity and UV detection (230 nm) after chemical suppression and inline sample preparation by dialysis.

Determination of traces of fluoride, chloride, bromide, nitrate, and sulfate in a boiler feed water containing 10 mg/L ammonia using anion chromatography with conductivity detection after chemical suppression and inline sample preparation by cation exchange.

Determination of traces of fluoride, acetate, formate, chloride, and sulfate in an ion exchanger eluate containing 2 g/L nitrate using anion chromatography with a step gradient and conductivity detection after chemical suppression.

Determination of the method detection limit (MDL) and method quantification limit (MQL) of bromate in drinking water using anion chromatography with conductivity detection after chemical suppression.

Determination of acetate, chloride, and sulfate in mayonnaise using anion chromatography with conductivity detection after chemical suppression and inline sample preparation by dialysis.

Determination of lactate, formate, chloride, phosphate, and sulfate in orange juice using anion chromatography with conductivity detection after chemical suppression and inline sample preparation by dialysis.

Determination of chloride, nitrite, nitrate, and sulfate in betaine using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrite, bromide, nitrate, and sulfate in inositol using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, sulfite, sulfate, oxalate, and thiosulfate in lignin using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, bromide, nitrate, sulfate, and trifluoroacetate (TFA) in a peptide sample using anion chromatography with conductivity detection after chemical suppression.

Determination of traces of chloride in a quaternary ammonium hydroxide using anion chromatography with conductivity detection after chemical suppression and inline cation exchange to remove the matrix cations.

Determination of acetate, chloride, nitrate, phosphate, and sulfate in mayonnaise using anion chromatography with conductivity detection after chemical suppression and advanced dialysis for inline sample preparation.

Determination of fluoride, chloride, and sulfate in an absorption solution containing H2O2 using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, acetate, formate, chloride, nitrite, nitrate, phosphate, and sulfate in wastewater containing N-methylpyrrolidone using anion chromatography with conductivity detection after chemical suppression and inline matrix elimination.

Determination of fluoride, chloride, nitrite, bromide, nitrate, phosphate, sulfate, and iodide in a mineral water using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride in a child's sweat using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrite, nitrate, phosphate, and sulfate in a strongly alkaline solution using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrite, and sulfate in a used zinc bath using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, phosphate, and sulfate in beer wort using anion chromatography with conductivity detection after chemical suppression.

Determination of 21 anions and organic acids using anion chromatography with conductivity detection after chemical suppression and applying a high pressure gradient.

Determination of fluoride, chloride, nitrite, bromide, nitrate, phosphate, and sulfate in water from an agricultural irrigation system using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, acetate, formate, and chloride in gasoline using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, acetate, formate, and chloride in a brake fluid using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, selenite, phosphate, nitrate, sulfate, and selenate using anion chromatography with conductivity detection after chemical suppression.

Determination of formate, chloride, nitrite, phosphite, phosphate, sulfite, nitrate, and sulfate using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride and bromide in an absorption solution after Wickbold digestion using anion chromatographywith conductivity detection after chemical suppression.

Determination of chloride in bethanechol tablets using anion chromatography with conductivity detection after chemical suppression.

Determination of trace levels of chloride, nitrate, phosphate, and sulfate in a boiler feed water using anion chromatography with conductivity detection after chemical suppression.

Qualitative determination of chloride, phosphate, and sulfate as well as chlorite, nitrite, chlorate, bromide, and chromate in urine using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrite, nitrate, and sulfate in a closed cooling water system using anion chromatography with conductivity detection after chemical suppression.

Determination of glycolate, formate, chloride, nitrite, nitrate, phosphate, sulfate, and oxalate in engine coolant using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrate, phosphate, and sulfate in a borate effluent using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, phosphate, sulfite, bromide, nitrate, and sulfate in a beer using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, bromide, nitrate, phosphate, and sulfate in dimethylacetamide using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, chloride, nitrate, sulfate, and oxalate in a perfluorocarbon material using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride and sulfate in an electrolyte used in sensors for transcutaneous CO2 measurement using anion chromatography with conductivity detection after chemical suppression.

Fast and reliable analysis of drinking water by combining EPA method 300.1 Parts A and B in a single IC run.

Determination of chloride and sulfate in ethanol using anion chromatography with conductivity detection after chemical suppression.

Determination of fluoride, glycolate, acetate, formate, chloride, nitrite, nitrate, and sulfate in the primary cycle water of a pressurized water reactor (PWR) using anion chromatography with conductivity detection after chemical suppression calibrated with Metrohm Inline Calibration.

Determination of chloride, chlorate, and sulfate in soda lye (50% sodium hydroxide) using anion chromatography with conductivity detection after sequential suppression and Metrohm Inline Neutralization.

Determination of chloride, sulfite, sulfate, and thiosulfate in a process water using anion chromatography with conductivity detection after chemical suppression and subsequent UV/VIS detection.

Determination of fluoride, acetate, propionate, formate, butyrate, chloride, nitrite, bromide, nitrate, benzoate, phosphate, sulfate, malonate, and oxalate in an industrial process water using anion chromatography with conductivity detection after sequential suppression.

Determination of formate, chloride, nitrate, phosphate, and sulfate in 20% TMAOH using anion chromatography with conductivity detection after sequential suppression and inline matrix neutralization.

Determination of chloride, nitrate, and sulfate in 85% H3PO4 using two-dimensional anion chromatography with conductivity detection after sequential suppression.

Determination of fluoride, acetate, formate, chloride, sulfate, malonate, succinate, and oxalate in Bayer liquor using anion chromatography with conductivity detection after sequential suppression.

Determination of the cross contamination of 100 mg/L of fluoride, chloride, nitrite, bromide, nitrate, phosphate, and sulfate to ultrapure water using anion chromatography with conductivity detection after chemical suppression and inline ultrafiltration.

Determination of fluoride, hypophosphite, chlorite, bromate, chloride, nitrite, bromide, chlorate, nitrate, phosphite, phosphate, sulfate, arsenate, iodide, chromate, and perchlorate using anion chromatography with conductivity detection after gradient elution and chemical suppression.

Determination of chloride, nitrate, sulfate, phosphate, and citrate using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, and sulfate in produced water using anion chromatography with conductivity detection after chemical suppression.

Determination of chloride, nitrate, and sulfate in cobalt acetate solution using anion chromatography with conductivity detection after sequential suppression using Metrohm Inline Dilution.

Determination of chloride, nitrite, nitrate, and sulfate in an ambient aerosol (PM2.5) using aerosol sampling with the PILS (Particle Into Liquid Sampler) and anion chromatography with conductivity detection after sequential suppression.

Determination of fluoride, acetate, formate, chloride, nitrite, nitrate, phosphate and sulfate in an E85 mixture (85% ethanol and 15% gasoline) by means of anion chromatography with conductivity detection and sequential suppression. The Inline Matrix Elimination serves as sample preparation.

Determination of fluoride, chloride, bromide, and iodide in petroleum coke after microwave combustion using anion chromatography with conductivity detection after sequential suppression.

Calibration of fluoride, chloride, nitrite, bromide, nitrate, phosphate, and sulfate using intelligent partial loop injection technique and anion chromatography with conductivity detection after sequential suppression. This technique allows a calibration range of 1:100 (e.g. 1 μg/L to 100 μg/L corresponding to 2 μL to 200 μL injected volume) out of 1 calibration solution. Applying the full range of partial loop injection to the samples one calibration covers a sample concentration range of 1 to 10'000.

Determination of fluoride, acetate, formate, chloride, nitrite, nitrate, phosphate, and sulfate impurities in syringe filters using anion chromatography with conductivity detection after sequential suppression.

Determination of fluoride, chloride, nitrate, phosphate, and sulfate on a short column or the ions mentioned plus bromate and nitrite on a long column in water samples applying intelligent column-switching using anion chromatography with conductivity detection after sequential suppression.

Determination of fluoride, chloride, and nitrate in concentrated sulfuric acid (96…98%) using anion chromatography with conductivity detection after sequential suppression.

Determination of chloride, nitrite, bromide, nitrate, phosphate, sulfite, sulfate, and oxalate in a cooling lubricant using anion chromatography with conductivity detection and subsequent UV detection (see AN-U-047) after sequential suppression and Metrohm Inline Dialysis.

Determination of fluoride, formate, acetate, chloride, nitrite, bromide, nitrate, sulfate, oxalate, and molybdate using anion chromatography with conductivity detection after chemical suppression and Metrohm Inline Dialysis.