Application Finder

This Bulletin is a supplement to Application Bulletin no. 36 (Half-wave potentials of inorganic substances) in the sense that the half-wave potentials of 100 different organic substances are listed. At the same time the supporting electrolytes used and the limits of determination are given.The various substances are listed in alphabetical order. The most important polarographically active functional groups are taken into consideration. This means that substances for related structures can also be determined polarographically in the same or similar supporting electrolytes, although they may not appear in the list.Unless otherwise stated, the half-wave potentials refer to a temperature of 20 °C, and the potentials are given in volts, measured with a sat. KCI-Ag/AgCl electrode assembly.The determination limits give the smallest concentrations which can be measured without risking serious errors in the results. In all cases, the limit of detection lies below the limit of determination.

Differential electrochemical mass spectrometry (DEMS) is used to monitor gaseous and volatile species during electrochemical reactions in situ.

Weak, organic bases that are soluble in nonaqueous solvents (including nonpolar solvents) are determined in glacial acetic acid using titration with strong acids, e. g., anhydrous perchloric acid or trifluoromethanesulfonic acid. The endpoint of such titrations can be determined thermometrically, insofar as a suitable thermometric endpoint indicator exists. The exceptional suitability of isobutyl vinyl ether (IBVE) as indicator has been demonstrated.

This Application Note shows how, with the help of Vis-NIR spectroscopy and a special plant library, 46 different medicinal and aromatic plants, e.g., Organicum majoricum and Tilia cordata, can be conveniently identified on the basis of their spectrum. In comparison with alternative methods for the determination of plants, which are elaborate and require experienced scientists for their performance, the Vis-NIR method permits rapid and uncomplicated identification.

Naphtha is the first petroleum product during the distillation process of crude oil or coal tar. It is primarily used as a base material for the production of gasoline or as a solvent. Accidental spills occur regularly at many locations throughout the world, leading to soil contamination.Investigation of contaminated sites is usually performed using gas chromatography, for which the soil sample has to be frozen, grinded, and subsequently extracted prior to the analysis. Using Visible-Near Infrared Spectroscopy such sample preparation steps are not necessary at all, making this method a viable, fast, and simple to use alternative.

Determination of L-lactide, citrate, and lactate in an acetone solution using ion-exclusion chromatography with direct conductivity detection.

Scrubber solutions for scrubbing flue gas often contain amines for absorbing acid gases, e.g., sulfur dioxide (SO2). 1-(2-hydroxyethyl)piperazine and 1,4- Bis(2-hydroxyethyl)piperazine from gas scrubber solutions are separated in the Metrosep Carb 2 - 150/4.0 column and then determined using pulsed amperometric detection.

This Application Note describes the rapid and non-destructive identification of conventional organic solvents using hand-held Raman spectrometers. Measurements with the handheld Raman spectrometer Mira M-1 require no sample preparation and provide immediate and unambiguous results.

Determination of tranexamic acid in injection solutions by nonaqueous potentiometric titration with perchloric acid using a glass electrode.

The epoxy content of epoxy resins has a strong influence on the reactivity of the resins as well as on the properties of the coating obtained from the resin curing process. The epoxy content is thus an important quality control parameter for manufacturers as well as consumers. This analysis is based on the reaction of hydrogen bromide with the epoxy groups of the sample. Hydrogen bromide in turn is produced by the reaction of tetraethylammonium bromide (TEABr) with standardized perchloric acid. The standards EN ISO 3001 and ASTM D1652 describe the determination of the epoxy content expressed as epoxy equivalent weight (EEW) by titration. The use of a Titrando and Solvotrode easyClean instead of manual titration greatly increases the reproducibility and repeatability of the determination.

This Application Note describes the nonaqueous acid-base titration of ketoconazole in accordance with the European Pharmacopoeia. The Solvotrode easyClean was used as the electrode.

Determination of penicillin G potassium and 2-phenyl acetamide in accordance with USP 28-NF 23 (Appendix 2) using RP chromatography and subsequent UV detection. Keyword: Antibiotics

Determination of clothiapine in a pharmaceutical standard.