水溶液中过氧化氢含量的测定
AN-T-025
2020-04
zh
Reliable and inexpensive determination according to ASTM D2180
过氧化氢具有杀菌作用，通常用于消毒和水处理。家庭中使用的过氧化物浓度较低，为 0.3-3%，而浓度较高的过氧化物则可用于消毒目的。此外，过氧化物还可用作氧化剂和漂白剂。过氧化物、过硼酸盐和过碳酸盐可通过滴定法轻松测定。本应用报告介绍了两种过氧化物分析的滴定方法： ASTM D2180 适用于浓过氧化氢溶液，第二种方法适用于痕量测定过氧化氢，浓度低至 0.4 mg/L。
Peroxides are often used for disinfection and water treatment purposes due to their antiseptic properties. Lower concentrations between 0.3–3% are used in households, while higher concentrations can be used for sterilization purposes.
Additionally, peroxides are utilized as oxidizing and bleaching agents. They are used for pulp and paper bleaching, as well as a mild whitener in laundry detergents and some cosmetic dental products.
Peroxides, perborates, and percarbonates can easily be determined by titration. This application note presents two titration methods for peroxide analysis. The first method is performed according to ASTM D2180, and is suitable for samples such as bleaching components or concentrated hydrogen peroxide solutions. The second method for the determination of traces of hydrogen peroxide is suitable for aqueous samples with concentrations as low as 0.4 mg/L.
This application study is demonstrated on aqueous solutions containing various hydrogen peroxide concentrations ranging from 0.4 mg/L to 32%.
Samples with traces of H2O2 do not require any sample preparation. Samples with higher concentrations are diluted with deionized water. Both sample size and dilution factor should be chosen depending on the expected peroxide content. Ideally, an aliquot of the diluted sample results in an equivalence point of approximately 10 mL.
The analysis is performed on an OMNIS Advanced Titrator equipped with a combined Pt ring electrode according to ASTM D2180. Before titration, the sample is acidified with sulfuric acid. In case of trace amounts, the sulfuric acid is modified to contain manganese sulfate as a catalyst. This modification allows a lower method detection limit.
Samples are titrated with potassium permanganate until after the equivalence point is reached. For samples with trace amounts of hydrogen peroxides, a lower titrant concentration is used.
Sharp titration curves with a large potential difference are obtained for all tested samples and with both methods. This results in reproducible results as displayed in Table 1.
| No | n | Mean value | SD(abs) | SD(rel) |
|---|---|---|---|---|
| 1 | 8 | 32.14% | 0.03% | 0.09% |
| 2 | 3 | 85.82 mg/L | 0.83 mg/L | 0.97% |
| 3 | 3 | 4.27 mg/L | 0.01 mg/L | 0.23% |
| 4 | 5 | 0.40 mg/L | 0.01 mg/L | 2.50% |
Titration is a fast and inexpensive method, allowing reliable determination of peroxides in aqueous solutions according to ASTM D2180. A modified method for trace concentrations permits accurate and reproducible peroxide determinations as low as 0.4 mg/L.
State-of-the-art OMNIS Titrators from Metrohm provide a whole new level of titration. The modular design of OMNIS Titrators offers complete application flexibility. The system can be expanded whenever necessary, allowing growth over time. With a resolution of 100,000 steps, maximum dosing accuracy can be achieved, further improving reproducibility.
分享应用
下载PDF
Internal references: AW TI CH1-1296-012020; AW TI CH1-0350-0187