856 Conductivity Module with Touch Control, including 5-ring conductivity measuring cell

856 Conductivity Module with Touch Control, including 5-ring conductivity measuring cell
Beställningsnummer: 2.856.0110

High-end conductometer, based on the 856 Conductivity Module, including 900 Touch Control, 5-ring conductivity measuring cell and calibration standards.

With the 856 Conductivity Module, not only conductivity and temperature can be determined, but also TDS and salinity. It supports state-of-the-art conductivity measuring cells, i.e. 5-ring measuring cells. Thanks to the galvanically isolated measuring input, pH value and conductivity can be measured in the same beaker without interference.

The Conductivity Module has two USB interfaces for connecting printers, barcode readers or sample changers and four MSB interfaces for stirrers or Dosinos. In combination with the 900 Touch Control, the 856 Conductivity Module is in compliance with GLP and FDA 21 CFR part 11 requirements.

  • Dokument
  • Ingående delar och tillbehör
  • Alternativ

Ladda ner hela leveransomfattningen och extra tillbehör som PDF

  • 5-ring conductivity measuring cell c = 0.7 cm-1 with Pt1000 (fixed cable)
    6.0915.100
    5-ring conductivity measuring cell c = 0.7 cm-1 with Pt1000 (fixed cable)

    5-ring conductivity measuring cell with cell constant c = 0.7 cm-1, with integrated Pt1000 temperature sensor and with fixed cable (1.2 m) for connecting to an 856 Conductivity Module.
    This sensor is suitable for measurements of medium conductivities (5 uS/cm to 20 mS/cm), e.g., in:

    • drinking water
    • surface water
    • wastewater

    1 piece(s)

  • Support stand without support rod
    6.2001.060
    Support stand without support rod
    To attach an 801, 804, 803 Stirrer to a Titrando, Titrino plus, Dosimat plus or 856 and 867.

    1 piece(s)

  • Clamping ring
    6.2013.010
    Clamping ring

    For support rods with a diameter of 10 mm.


    1 piece(s)

  • Support rod / 400 mm
    6.2016.070
    Support rod / 400 mm

    1 piece(s)

  • Electrode holder
    6.2021.020
    Electrode holder
    Electrode holder for 4 electrodes and 2 buret tips

    1 piece(s)

  • Conductivity standard 100 µS/cm, 5 x 30 mL
    6.2324.110
    Conductivity standard 100 µS/cm, 5 x 30 mL
    Conductivity standard for calibration of conductivity measuring cells with cell constant = 0.1/cm.

    1 piece(s)

  • 
    5 mm hex key for IC Sample Processors
    6.2621.070
    5 mm hex key for IC Sample Processors

    1 piece(s)

  • Hexagon key 2 mm
    6.2621.130
    Hexagon key 2 mm
    2 mm.

    1 piece(s)

  • USB Memory Stick for 900 Touch Control 
    6.6064.010
    USB Memory Stick for 900 Touch Control 

    1 piece(s)

Ladda ner hela leveransomfattningen och extra tillbehör som PDF

  • USB thermal printer Neo's
    2.141.0100
    USB thermal printer Neo's

    Compact printer with USB interface for the Ti-Touch, the Titrino plus and Dosimat plus and the 91X Meter instruments.

    Paper width 60 mm (40 characters). Including 6.2151.120 USB cable.

  • 
    801 Stirrer
    2.801.0010
    801 Stirrer

    Magnetic stirrer without stand for supplementing the Titrino plus, Dosimat plus, Titrandos, Sample Processors, 805 Dosimats and 780/781 pH Meters. With permanently attached cable for MSB (Metrohm Serial Bus).


  • 814 USB Sample Processor (1T/1P)
    2.814.0010
    814 USB Sample Processor (1T/1P)

    USB Sample Processor with one workstation and one built-in membrane pump for the automatic processing of routine samples in series with small to medium quantities. In addition to the built-in pump, an additional one (membrane or peristaltic) and up to three dosing devices for Liquid Handling tasks can be connected.

    Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.

  • 814 USB Sample Processor (1T/2P)
    2.814.0020
    814 USB Sample Processor (1T/2P)

    USB Sample Processor with one workstation and two built-in membrane pumps for the automatic processing of routine samples in series with small to medium quantities. In addition to the built-in pumps, up to three dosing devices for Liquid Handling tasks can be connected.

    Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.
     

     

  • 814 USB Sample Processor (1T/0P)
    2.814.0030
    814 USB Sample Processor (1T/0P)

    USB Sample Processor with one workstation for the automatic processing of routine samples in series with small to medium quantities. Up to two pumps (membrane or peristaltic) and three dosing devices for Liquid Handling tasks can be connected.

    Because of the multitude of application variants, rack, stirrer, titration head, Swing Head and sample vessels must be tailored to the application and ordered separately.
     

  • 5-ring conductivity measuring cell c = 1.0 cm-1 with Pt1000 (fixed cable)
    6.0915.130
    5-ring conductivity measuring cell c = 1.0 cm-1 with Pt1000 (fixed cable)

    5-ring conductivity measuring cell with cell constant c = 1.0 cm-1, with integrated Pt1000 temperature sensor and with fixed cable (1.2 m) for connecting to an 856 Conductivity Module in combination with a sample changer.
    This sensor is suitable for automated measurements of medium conductivities (5 uS/cm to 100 mS/cm), e.g., in:

    • drinking water
    • surface water
    • wastewater
  • Conductivity measuring cell c = 0.1 cm-1 with Pt1000 (fixed cable)
    6.0916.040
    Conductivity measuring cell c = 0.1 cm-1 with Pt1000 (fixed cable)

    Conductivity measuring cell made of stainless steel with cell constant c = 0.1 cm-1, with integrated Pt1000 temperature sensor and fixed cable (1.2 m) for connecting to an 856 Conductivity Module.
    This sensor is suitable for measurements of low conductivities (0 uS/cm to 300 uS/cm) in e.g., deion. water or for measurements in accordance with USP <645>.

  • 5-ring conductivity measuring cell c = 0.7 cm-1 with Pt1000 (fixed cable 2 m)
    6.0920.100
    5-ring conductivity measuring cell c = 0.7 cm-1 with Pt1000 (fixed cable 2 m)

    5-ring conductivity measuring cell with cell constant c = 0.7 cm-1, with integrated Pt1000 temperature sensor and fixed cable (2.0 m) for connecting to an 856 Conductivity Module in combination with a sample changer.
    This sensor is suitable for automated measurements of medium conductivities (5 uS/cm to 20 mS/cm), e.g., in:

    • drinking water
    • surface water
    • wastewater
  • 5-ring conductivity measuring cell c = 1.0 cm-1 with Pt1000 (fixed cable 2 m)
    6.0920.130
    5-ring conductivity measuring cell c = 1.0 cm-1 with Pt1000 (fixed cable 2 m)

    5-ring conductivity measuring cell with cell constant c = 1.0 cm-1, with integrated Pt1000 temperature sensor and fixed cable (2.0 m) for connecting to an 856 Conductivity Module in combination with a sample changer.
    This sensor is suitable for automated measurements of medium conductivities (5 uS/cm to 100 mS/cm), e.g., in:

    • drinking water
    • surface water
    • wastewater
  • Stacking frame for 846 Dosing Interface, 856 Conductivity Module, 867 pH Module
    6.2065.000
    Stacking frame for 846 Dosing Interface, 856 Conductivity Module, 867 pH Module
    For fixing the Reagent Organizer on top of the Dosing Interface
  • Adapter 4 x socket B – plug N
    6.2103.160
    Adapter 4 x socket B – plug N
    Adapter box for the connection of classical Metrohm Conductivity measuring cells with 4 banana plugs to the 856 Conductivity Module.
  • Cable USB A – mini-DIN 8-pin
    6.2151.000
    Cable USB A – mini-DIN 8-pin
    Controller cable