TitrIC pro II - The hyphenated IC and titration system for complete anion and cation analysis

Additional equipment for Robotic Sample Processors XL without titration or transfer heads.

Drive with write/read hardware for intelligent Dosing Units. With fixed cable (length 150 cm).

Rod stirrer for sample changer and Sample Processor.

With 6.1909.020 Propeller stirrer 104 mm and fixed cable.

Robotic USB Sample Processor XL with one workstation and two built-in membrane pumps for the automatic processing of routine samples in series with large quantities and for complex sample preparation or parallel runs. Up to three dosing devices for Liquid Handling tasks can be connected.

Because of the multitude of application variants, rack, stirrer, titration head, robotic arm, Swing Head and sample vessels must be tailored to the application and ordered separately.
 

Compact and intelligent high performance conductivity detector for intelligent IC instruments. Outstanding temperature stability, the complete signal processing within the protected detector block and the latest generation of DSP – Digital Signal Processing – guarantee the highest precision of the measurement. No change of measuring ranges (not even automatic ones) is required, due to the dynamic working range.

Conductivity measuring module as supplement to an existing Titrando system or "stand-alone" in combination with a 900 Touch Control. With the 856 Conductivity Module, not only conductivity and temperature can be determined, but also TDS and salinity. It supports state-of-the-art conductivity measuring cells, i.e. 5-ring measuring cells.
Thanks to the galvanically isolated measuring input, pH value and conductivity can be measured in the same beaker without interference.

The Conductivity Module is equipped with two USB interfaces for connecting printers, barcode readers or sample changers and four MSB interfaces for stirrers or Dosinos.
Both in conjunction with the 900 Touch Control as stand-alone instrument and also integrated in tiamo™ full (from 2.0), it is in compliance with GLP and FDA 21 CFR part 11 requirements.

High-end titrator for potentiometric titration with one measuring interface for use with Dosino dosing systems.
 

• up to four dosing systems of the 800 Dosino type
• dynamic (DET), monotonic (MET) and endpoint titration (SET)
• Measurement with ion-selective electrodes (MEAS CONC)
• Dosing functions with monitoring, Liquid Handling
• four MSB connectors for additional stirrers or dosing systems
• "iTrode" intelligent electrodes
• USB connector
• For use with tiamo PC software or Touch Control unit
• Compliance with GMP/GLP and FDA regulations such as 21 CFR Part 11, if required

Intelligent, combined pH electrode with integrated memory chip for storing sensor data and with Pt1000 temperature sensor for pH measurements/titrations in ion-deficient aqueous media (e.g., drinking water, process water). This electrode shows a very short response time in these samples.

The fixed ground-joint diaphragm is insensitive to contamination.
When c(KCl) = 3 mol/L is used as bridge electrolyte, storage in storage solution is recommended.
The bridge electrolyte can be easily replaced with a chloride-free electrolyte (e.g., potassium nitrate c(KNO₃) = 1 mol/L (6.2310.010)). Storage in the used bridge electrolyte.
iTrodes can be connected to Titrando, Ti-Touch, or 913/914 meters.

5-ring conductivity measuring cell with cell constant c = 0.7 cm^-1, with integrated Pt1000 temperature sensor and with fixed cable (1.2 m) for connecting to an 856 Conductivity Module.
This sensor is suitable for measurements of medium conductivities (5 uS/cm to 20 mS/cm), e.g., in:

• drinking water
• surface water
• wastewater

Transfer robotic arm for liquid handling purposes

Aspiration tip for the Sample Processors.

Stopper with three buret tips for connecting 3 x M6 tubing

Adapter for bottles with S40 thread (Merck...) to GL45.

With light and kink protection

With light and kink protection

With light and kink protection

2 M6 outer threads. Part of the screw connections for Exchange Units and 676 Sample Changer

3 M6 inner threads.

Adapter for use with Dosino port 4 in IC. For connecting to M6 connector.

For sample changers for transferring larger-sized sample volumes, e.g. for brightener determination.

Support stand for Sample Processors, for external titrations and dilutions (IC)

Mounting part for Dosinos at the IC instrument housing.

For the Metrohm RS-232 interface - PC connection. For Titrinos, Titrino plus and 756, 831 KF Coulometer, RS-232/USB Box

Extends the 900 Touch Control by an RS-232 interface for the connection of e.g. balance. 

Controller cable

Mixed buffer solutions pH 4.00/7.00/9.00 (25 °C) in single use sachets, colourless, box of 3 x 10 x 30 mL

Maintenance kit for pH electrodes

The kit contains:

• 50 mL cleaning solution
• 50 mL 3M KCl solution
• 50 mL storage solution
• 2 Storage vessels
• Instructions for use

On Sample Processors

PTFE. Used with 6.5613.000 ECO titration equipment

With E.301.0041 O-ring. For 6.1448.010 Septum and 6.1414.030 Titration vessel lid. Used for KF applications.

Complete with nipple and O-ring. For 6.1414.030 titration vessel lids. For KF instruments, VA measurement stands, VA Computrace and IC Dilution.

PCTFE. With M16 thread. Used with 6.5613.000 ECO titration equipment

PCTFE. Used with 6.5613.000 ECO titration equipment with 722 Stirrer

Short version. With UNF 10/32 connection. 5 pieces. For the connection of PEEK capillaries

With M6 outer thread. For IC instruments.

Flow-through cell for the 6.0915.100/6.0920.100 5-ring conductivity measuring cell

For IC/VA Sample Processors. For 1/8 in. tubes

Dosing unit with integrated data chip with 20 mL glass cylinder and light protection, mountable on reagent bottle with ISO/DIN GL45 thread. FEP tubing connection, anti-diffusion buret tip.

Dosing unit with integrated data chip with 50 mL glass cylinder and light protection, mountable on reagent bottle with ISO/DIN GL45 thread. FEP tubing connection, anti-diffusion buret tip.

tiamo™ 2.3 Light computer program for controlling a titration system.

• Up to two instruments can be connected
• Graphical method editor with numerous templates
• Layout manager for individual monitor interface
• Professional database with reevaluation
• High-performance report generator
• No parallel titration, no data export
• Dialog languages: German, English, French, Italian, Spanish, Portuguese, Polish, Russian, Slovakian, Japanese, Chinese, Traditional Chinese